DI801机器人模块卡件
程序模式未初始化
所有输出都被关闭。当它因关闭而出现问题时，单击模式键，并从报警检查状态输出屏幕中删除。7-9.初始化设置参数如果要将设置内容返回到初始值，可以通过以下步骤进行。有两种类型的初始化，您可以从中进行选择。一旦执行初始化，您将无法返回到原始设置内容，因此请小心。正在初始化的初始化类型程序屏幕1.初始化基本设置内容（模式0至模式11）。然而，程序模式未初始化。① 切断电源。② 打开电源，同时单击 钥匙③ 确认显示右侧显示的屏幕后，释放 钥匙④ 初始化完成后，将显示操作屏幕。
初始化所有设置内容
（模式0至模式11），程序模式也被初始化。① 切断电源。② 在按下的同时打开电源 键和 钥匙③ 确认显示右侧显示的屏幕后，释放 键和 钥匙④ 初始化完成后，将显示操作屏幕。*'外部信号分配“未初始化。预防措施当显示时间信号输出测试和检查状态输出时，输出的当前状态关闭。当出现关闭问题时，单击模式键，从设置屏幕中删除或在模式屏幕中设置“NoDisp”。-38-7-10.设置注意事项说明1.设置范围的注意事项。･在数值设置参数中，存在可设置的数值范围，因此请小心如果尝试设置的数值超出了可以设置的数值范围，则会显示错误消息。当显示错误消息时，确认错误消息的内容并进行正确的设置。2.更改设置时，有时其他设置屏幕的设置内容也会更改。▪如果更改重要关键参数的设置，小数点位置或其他相关设置屏幕的设置值的设置范围有时可能会更改或初始化例如，如果模式5的“SV小数点”、“SV刻度”等发生变化，与之相关的其他设置屏幕的设置内容也会发生变化如果更改了这些关键参数的设置，请重新确认其他设置屏幕的设置内容。
Program mode not initialized
All outputs are turned off. When it has problems because it is turned off, click the Mode key and delete it from the Alarm Check Status Output screen. 7-9. Initialize setting parameters If you want to return the setting content to the initial value, you can do it through the following steps. There are two types of initialization from which you can choose. Once initialization is performed, you will not be able to return to the original settings, so be careful. Initializing the initialization type program screen 1. Initialize the basic settings content (mode 0 to mode 11). However, the program mode is not initialized. ① Cut off the power. ② Turn on the power supply and click the key ③ to confirm the display of the screen displayed on the right. After the key ④ is released and the initialization is completed, the operation screen will be displayed.
Initialize all settings
(mode 0 to mode 11), the program mode is also initialized. ① Cut off the power. ② While pressing, turn on the power key and the key ③ to confirm the display of the screen displayed on the right, and then release the key and the key ④ to display the operation screen after the initialization is completed. * " External signal assignment "uninitialized. Precautionary Action When the time signal output test and check status output is displayed, the current status of the output is closed. When a shutdown problem occurs, click the mode key to delete from the setup screen or set" NoDisp "in the mode screen- 38-7-10. Notes on setting 1. Notes on setting range In the numerical setting parameters, there is a range of values that can be set, so be careful if you try to set a value that exceeds the range of values that can be set, an error message will be displayed. When the error message is displayed, confirm the content of the error message and make the correct settings. 2. When changing settings, sometimes the settings on other settings screens will also change. ▪ If the settings of important key parameters are changed, the decimal point position or the setting range of other related setting screens may sometimes be changed or initialized. For example, if the "SV decimal point" and "SV scale" of mode 5 change, the settings of other related setting screens will also change. If the settings of these key parameters are changed, please reconfirm the settings of other setting screens.
