DFI-110-340F工控模块机器人备件
钥匙背光
① 设置按键背光的照明/非照明功能。② 如果选择“自动”，将进行以下操作通常它不亮，但当电源接通或按下任何键时，它会亮起，如果在大约30秒内未进行任何键操作，则会关闭。③ 如果选择“OFF”（关闭），通常会关闭。④ 如果选择“ON”（打开），通常会亮起。-36-
外部信号布局
① 仅显示外部信号输入规格或外部信号输出规格。② 在外部信号输入（DI）和外部信号输出（DO）中，分配了端子号功能。③ 在“端子号”中，显示具有外部信号输入（DI）或外部信号输出（DO）功能的端子号，从而设置端子号（编号）及其对应的功能。④ 外部信号输入（DI）功能如下“运行/停止”：程序驱动。关闭时运行，关闭时停止。从ON（瞬时信号）前进到OFF。▪“复位”：程序驱动。ON（瞬时信号）时重置等待：程序驱动器。打开时等待。▪“快速”：程序驱动器。打开时加速。▪“PTN 1”：选择模式。打开时BCD代码为“1”。▪“PTN 2”：选择模式。打开时BCD代码为“2”。▪“PTN 4”：选择模式。打开时BCD代码为“4”。▪“PTN 8”：选择模式。打开时BCD代码为“8”。▪“PTN10”：选择模式。打开时BCD代码为“10”。▪“PTN20”：选择模式。打开时BCD代码为“20”。⑤ 外部信号输出（DO）功能如下来自“TS1”：时间信号。从时间信号1。▪到“TS8”：时间信号。至时间信号8.･“运行/停止”：状态。打开时运行，关闭时停止。打开时前进（瞬时信号）“复位”：状态。打开时重置。▪“等待”：状态。打开时等待。▪“结束”：状态。打开时结束。⑥ 从工厂发货时，未显示设置条件“---------------------”。如果设置任何功能一次，则不显示未设置条件。⑦ 即使设置内容已初始化，分配的设置也不会初始化。
Key backlight
① Set the lighting/non lighting function of the key backlight. ② If "Automatic" is selected, the following operations will be performed. Generally, it is not lit, but it will be lit when the power is turned on or any key is pressed. If no key operation is performed in about 30 seconds, it will be turned off. ③ If "OFF" is selected, it is usually turned off. ④ If "ON" is selected, it usually lights up- 36-
External signal layout
① Only external signal input specifications or external signal output specifications are displayed. ② In the external signal input (DI) and external signal output (DO), the terminal number function is assigned. ③ In "Terminal number", the terminal number with external signal input (DI) or external signal output (DO) function is displayed, so as to set the terminal number (number) and its corresponding function. ④ The function of external signal input (DI) is as follows: "run/stop": program drive. Runs when closed and stops when closed. Advance from ON (instantaneous signal) to OFF. ▪ "Reset": program driver. Reset wait when ON (instantaneous signal): program driver. Wait while opening. ▪ "Fast": program driver. Accelerate when open. ▪ "PTN 1": Select the mode. The BCD code is "1" when opened. ▪ "PTN 2": Select the mode. The BCD code is "2" when opened. ▪ "PTN 4": Select the mode. The BCD code is "4" when opened. ▪ "PTN 8": Select the mode. The BCD code is "8" when opened. ▪ "PTN10": Select the mode. The BCD code is "10" when opened. ▪ "PTN20": select the mode. The BCD code is "20" when opened. ⑤ The external signal output (DO) function comes from "TS1" as follows: time signal. Slave time signal 1. ▪ To "TS8": time signal. To time signal 8. ¥ "Run/Stop": status. Runs when turned on and stops when turned off. Forward when open (instantaneous signal) "reset": status. Reset on open. ▪ "Waiting": status. Wait while opening. ▪ "End": status. End on open. ⑥ When shipping from the factory, the set condition "---------------------" is not displayed. If any function is set once, the unset condition is not displayed. ⑦ The assigned settings are not initialized even if the settings are initialized.
