CP-A RU工控DCS系统备件
模式选择系统
① 仅显示具有外部信号输入或通信的规格。② 设置了模式选择系统。③ 如果选择了“键”，则使用前键进行选择。④ 如果选择“EXT”，则使用外部信号输入进行选择。然而，它只能用于具有外部信号输入的规格。⑤ 如果选择“COM”，则使用通信进行选择。但是，只能选择具有通信功能的规格。⑥ 如果选择“FREE”（自由），则可以通过前键或外部信号输入或通信进行选择。然而，它只能用于具有外部信号输入的规格或具有通信的规格。此时，任何最后的选择操作都将成为最新的选择编号，然而，最后的选择系统类型无法从外观上判断，因此请小心。
时间显示系统
① 设置操作屏幕的时间显示系统（时间显示）。② 如果选择“通过步骤”，则显示执行步骤的经过时间。③ 如果选择“通过模式”，则显示执行模式的经过时间。④ 如果选择“保持步骤”，则显示执行步骤的剩余时间。⑤ 如果选择“保持模式”，则显示执行模式的剩余时间。⑥ 在时间显示屏幕中，时间显示系统也可以通过 钥匙
电源启动时的操作
① 启动电源时设置操作状态。② 如果选择“继续”，则状态为电源切断前的状态。③ 如果选择“复位”，则状态为复位状态。④ 当选择RESET（复位）并启动电源时，即使设置屏幕、外部信号输入和通信选择RUN（运行）状态，状态仍为RESET（重置），因此要小心。在这种情况下，通过再次返回RUN，状态变为“RUN”。
Mode selection system
① Only specifications with external signal inputs or communications are displayed. ② The mode selection system is set. ③ If Key is selected, use the front key to select. ④ If "EXT" is selected, external signal input is used for selection. However, it can only be used for specifications with external signal inputs. ⑤ If "COM" is selected, communication is used for selection. However, only specifications with communication functions can be selected. ⑥ If "FREE" is selected, it can be selected through the front key or external signal input or communication. However, it can only be used for specifications with external signal input or specifications with communication. At this time, any final selection operation will become the latest selection number. However, the final selection system type cannot be judged from the appearance, so please be careful.
Time display system
① Set the time display system of the operation screen (time display). ② If you select Pass Step, the elapsed time of executing the step is displayed. ③ If you select Pass Mode, the elapsed time of the execution mode is displayed. ④ If you select Hold Step, the remaining time to execute the step is displayed. ⑤ If you select Hold Mode, the time remaining to execute the mode is displayed. ⑥ In the time display screen, the time display system can also use the key
Operation during power startup
① Set the operation state when starting the power supply. ② If "Continue" is selected, the state is the state before the power is cut off. ③ If "Reset" is selected, the status is reset. ④ When RESET is selected and the power supply is started, the status is RESET even if RUN is selected for the setting screen, external signal input and communication, so be careful. In this case, the status changes to "RUN" by returning to RUN again.
