COM0032自动化模块
键在单击 按键
･当在设置屏幕期间单击时，该模式变为设置操作键模式，用于光标转发或选择字段。 ･在运行操作键模式下，它作为复位键运行。（例如，在操作屏幕中，如果 键在单击 键，状态为复位状态。）▪当在设置屏幕中单击时，该模式变为设置操作键模式，并按设置值（设置字段）的降序使用在运行操作键模式下，它作为PTN键运行。（例如，在操作屏幕中，如果在单击 复位时，状态变为模式编号选择状态。）当在设置屏幕中单击时，该模式变为设置操作键模式，并按设置值（或设置字段）的升序使用 ･用于注册设置屏幕的设置。① 1区端子号外部信号输入6点外部信号输出6点2区端子号内部信号输入6点外部信号输出5点3区端子号通信RS232C+外部数字输入3点通信RS422A+外部数字输出1点通信RS485+外部数字信号输入3点外部信号输入6点输出6点 RD RDA SA公司 SD RDB某人 斯格-斯达-斯格 软件开发银行 SG-12-终端号通信RS232C（1）+通信RS232B（2）+外部数字输入1点通信RS232A（1）+RS422A（2）+RS232C 1点通信外部数字输入RS485（2）+1点通信RS485+RS232C 2）+RS232A 1点通信数字输入1点通信RS485（1）+通信RS488（2）+外部数字输入1（注）通信2端口未绝缘。
端子号外部信号输入
8点外部信号输出8点外部信息输出5点+外部信息输入3点外部信息输入4点+外部信号输入4点-13-4-3-2接线基本注意事项为了避免事故，请务必阅读并理解这些内容。1.连接终端① 对于端子接线，使用带绝缘套管的压接式端子。始终使用O型端子以确保电源端子和接地端子的安全。对于其他类型的端子，我们还建议您使用O型端子。② 拧紧端子螺钉时，扭矩为“0.6至0.8 Nm”。如果施加的扭矩超过该值，则端子螺钉面板会损坏，因此请小心。2.电源端子① 在电源中，将符合设定器额定值的过电流保护装置和开关放置在3m范围内，以便于接近。② 使用带有600V乙烯基绝缘电线（额定值大于1A AC）和同等或更大电线的电源。③ 为避免故障，请使用电压变化小、波形存储和噪声小的优质单相电源。如果噪声很大，使用噪声滤波器和插入绝缘变压器等。④ 在额定电源的情况下，电流有少量泄漏，因此要小心。泄漏电流约为▪使用额定范围内的输出端子。如果连接了超出范围的负载，则设置器可能会出现故障，或者其性能会显著下降，或者可能出现故障。4.选项终端▪下部显示屏显示操作屏幕和设置屏幕。操作屏幕成为显示程序模式的进度时间的时间显示屏幕和整体显示屏幕。6-1.时间显示屏幕时间显示屏幕屏幕说明
Click
❑ When clicked during the setting screen, this mode changes to the setting operation key mode for cursor forwarding or field selection. It operates as a reset key in the operation key mode. (For example, in the operation screen, if you have not clicked the element key, the status is reset.) ▪ When clicked in the setting screen, this mode becomes the setting operation key mode, and is used in descending order of the setting value (setting field). In the operation key mode, it operates as PTN key. (For example, in the operation screen, if you click the element reset, the state changes to the mode number selection state.) When you click in the setting screen, the mode changes to the setting operation key mode, and you can use the settings for registering the setting screen in ascending order of the setting value (or setting field). ① External signal input of zone 1 terminal number 6 points external signal output 6 points internal signal input of zone 2 terminal number 6 points external signal output 5 points terminal number communication of zone 3 RS232C+external digital input 3 points communication RS422A+external digital output 1 point communication RS485+external digital signal input 3 points external signal input 6 points output 6 points, RD RDA SA, SD RDB, SEG - STAR - SEG, Software Development Bank, SG-12 - terminal number communication RS232C (1) +Communication RS232B (2)+external digital input 1-point communication RS232A (1)+RS422A (2)+RS232C 1-point communication external digital input RS485 (2)+1-point communication RS485+RS232C 2)+RS232A 1-point communication digital input 1-point communication RS485 (1)+communication RS488 (2)+external digital input 1 (note) Communication 2 port is not insulated.
Terminal No. External signal input
8-point external signal output 8-point external information output 5-point+external information input 3-point external information input 4-point+external signal input 4-point - 13-4-3-2 Wiring basic precautions To avoid accidents, please read and understand these contents. 1. Connection terminal ① For terminal wiring, crimp terminals with insulating sleeves shall be used. Always use O-ring terminals to ensure the safety of power and ground terminals. For other types of terminals, we also recommend that you use O-ring terminals. ② When tightening the terminal screws, the torque is "0.6 to 0.8 Nm". If the applied torque exceeds this value, the terminal screw panel will be damaged, so be careful. 2. Power terminal ① In the power supply, place the over-current protection device and switch that meet the rated value of the setter within 3m for easy access. ② Use a power supply with 600V vinyl insulated wire (rated above 1A AC) and equivalent or larger wire. ③ To avoid faults, please use high-quality single-phase power supply with small voltage change, waveform storage and low noise. If the noise is large, use noise filter and insert insulation transformer. ④ In the case of rated power supply, there is a small amount of leakage of current, so be careful. The leakage current is about ▪ Use the output terminals within the rated range. If an out of range load is connected, the setter may fail, or its performance may degrade significantly, or it may fail. 4. Option terminal ▪ The lower display shows the operation screen and the setup screen. The operation screen becomes the time display screen and the overall display screen to display the progress time of the program mode. 6-1. Time Display Screen Time Display Screen Description
