ASFC-01C控制器模块
接口规范打印机配置
有一个现金抽屉接口和一个数据接口（您可以选择并行接口、USB接口、USB端口+串行接口、USB口+以太网接口、USB连接+蓝牙或USB接口+Wi-Fi）。用合适的电缆连接计算机。2.1现金抽屉接口现金抽屉接口为RJ-11接口，如下所示。表A-1：现金抽屉连接器引脚分配引脚编号信号方向1框架接地---2现金抽屉驱动信号OUT 3现金抽屉打开/关闭信号IN 4 24V（DC）OUT 5现金抽屉驱动器信号OUT 6现金抽屉打开或关闭信号接地---驱动电流≤24V/1A 2.2并行接口TP830打印机的并行接口与Centronics协议兼容，支持BUSY/ACK握手协议，接口连接器为36 PIN Centronics类型。表A-2并行接口连接器的引脚功能表A-2:36 PIN并行接口引脚分配引脚号信号方向说明1/STB IN触发器处于低电平，在上升沿加载数据2 3 4 5 6 DATA1 DATA2 DATA3 DATA4 DATA5 in in in这些信号分别表示从第一位到第八位的并行数据。“1”表示高电平，而逻辑中的“0”表示低电平。图5-1现金抽屉界面图5-2并行界面注：请使用符合上述规格的现金抽屉。当使用未经授权的现金抽屉时，制造商将不履行保修。6 1表A-1：现金抽屉连接器引脚分配TP830用户手册-41-7 8 9 DATA6 DATA7 DATA8 IN IN 10/ACK OUT确认脉冲，低电平表示打印机已准备好接收数据。
接收数据
11 BUSY OUT高电平表示打印机太忙，无法接收数据。12 PE OUT高电平表示纸张用完。13 SEL OUT高电平，上拉电阻32/ERR OUT低电平表示打印机处于错误状态。14、15、17、18、34、36 NC--NC 16、19~30、33 GND-GND，逻辑中的“0”电平相对引脚规格如图5-3所示。2.3 USB接口USB接口为2.0全速版本。2.4串行接口TP830打印机的串行接口与RS-232C协议兼容，支持RTS/CTS和XON/XOFF握手协议。其连接器为DB-9型连接器，每个引脚的分配如图5-5所示。触点号信号名称颜色1 VBUS红色2 D-白色3 D+绿色4 GND黑色BUSY/ACK DATA/STB 0.5μs 0.5μs 0.5μs 0.5µs 0.5μs表a-2 36引脚并行接口引脚分配图5-3并行接口引脚规格图5-4 USB接口2 1 3 4注：① “IN”表示打印机输入，“OUT”表示打印机输出。② 信号的逻辑电平是TTL电平。TP830用户手册-42-表A-3：串行接口引脚分配引脚号信号来自说明2 RXD主机接收来自主机3 TXD打印机的数据发送控制代码X-ON/X-OFF和数据至主机8 CTS打印机“标记”状态表示打印机太忙，无法接收数据；“空格”表示打印机已准备好接收数据。5 GND-信号GND 4 DTR打印机数据终端就绪。串行连接方式的波特率和数据配置的默认设置为9600bps、8个数据位、禁用奇偶校验和1个停止位。
Interface specification printer configuration
There is a cash drawer interface and a data interface (you can select parallel interface, USB interface, USB port+serial interface, USB port+Ethernet interface, USB connection+Bluetooth or USB interface+Wi Fi). Connect the computer with a suitable cable. 2.1 Cash drawer interface The cash drawer interface is RJ-11 interface, as shown below. Table A-1: Cash Drawer Connector Pin Assignment Pin Number Signal Direction 1 Frame Grounding --- 2 Cash Drawer Drive Signal OUT 3 Cash Drawer Open/Close Signal IN 4 24V (DC) OUT 5 Cash Drawer Drive Signal OUT 6 Cash Drawer Open or Close Signal Grounding --- Drive Current ≤ 24V/1A 2.2 Parallel Interface TP830 Printer's parallel interface is compatible with Centronics protocol and supports BUSY/ACK handshake protocol, The interface connector is 36 PIN Centronics type. Table A-2 Pin function of parallel interface connector Table A-2: 36 Pin number signal direction of PIN parallel interface pin assignment indicates that 1/STB IN trigger is at low level, and data 2 3 4 5 6 DATA1 DATA2 DATA3 DATA4 DATA5 in in are loaded on the rising edge. These signals represent parallel data from the first bit to the eighth bit respectively. "1" indicates high level, while "0" in logic indicates low level. Figure 5-1 Cash Drawer Interface Figure 5-2 Parallel Interface Note: Please use a cash drawer that meets the above specifications. When unauthorized cash drawers are used, the manufacturer will not perform the warranty. 6 1 Table A-1: Cash Drawer Connector Pin AssignmentTP830 User Manual-41-7 8 9 DATA6 DATA7 DATA8 IN 10/ACK OUT Confirmation Pulse, low level indicates that the printer is ready to receive data.
receive data
11 BUSY OUT high indicates that the printer is too busy to receive data. 12 PE OUT high indicates that the paper is used up. 13 SEL OUT high and pull-up resistance 32/ERR OUT low indicate that the printer is in an error state. 14. 15, 17, 18, 34, 36 NC -- NC 16, 19~30, 33 GND-GND. The relative pin specifications of "0" level in logic are shown in Figure 5-3. 2.3 USB interface USB interface is 2.0 full speed version. 2.4 Serial interface The serial interface of TP830 printer is compatible with RS-232C protocol and supports RTS/CTS and XON/XOFF handshake protocols. The connector is DB-9 type connector, and the allocation of each pin is shown in Figure 5-5. Contact number signal name color 1 VBUS red 2 D-white 3 D+green 4 GND black BUSY/ACK DATA/STB 0.5 μ s 0.5 μ s 0.5 μ s 0.5µs 0.5 μ S Table a-2 36 pin parallel interface pin assignment Figure 5-3 Parallel interface pin specification Figure 5-4 USB interface 2 1 3 4 Note: ① "IN" represents printer input, and "OUT" represents printer output. ② The logic level of the signal is TTL level. TP830 User Manual - 42 - Table A-3: Serial interface pin assignment pin number signal comes from description 2 RXD host receives data from host 3 TXD printer Transmission control code X-ON/X-OFF and data to host 8 CTS printer "Mark" state indicates that the printer is too busy to receive data; "Space" indicates that the printer is ready to receive data. 5 GND signal GND 4 DTR printer data terminal is ready. The default settings for the baud rate and data configuration of the serial connection mode are 9600bps, 8 data bits, disable parity, and 1 stop bit.
