APOW-01C控制器模块
纸张安装
拉出少量纸张，如图所示放置，然后合上前盖。图4-4拉出纸张注意：完成纸张安装后，如果paper out LED和ERROR LED仍亮着，或者打印机在进纸时发出奇怪的噪音，请打开盖子并重新紧紧地合上。更正错误卷纸图4-3装纸方向注意：纸头应向下放置并拉向进纸槽，但不能相反。卷纸TP830用户手册-38-第5章规范5.1一般规范项目描述打印方法热线打印纸张馈送模式单向摩擦馈送纸张弹出方向从正面弹出点密度640点/行（203×203 DPI）打印宽度最大：80 mm，640点打印速度最大：300毫米/秒进纸速度最大：30毫米/秒行间距3.75毫米打印头寿命150公里，1X108脉冲切割器寿命150万切纸厚度0.065～0.14毫米TF50KS-E（日本纸业株式会社）热卷纸型号AF50KS-E（JUJO Thermal）宽度：79.5±0.5毫米；69.5±0.5毫米；57.5±0.5 mm重量：53～80 g/m2最大直径：Φ83 mm纸张厚度：0.065～0.14 mm纸张规格字符集ASCII：13个国际字符集接口此打印机可配备以下接口：并行接口：Centronics USB接口：2.0全速USB接口（2.0全速）+串行接口[RS-232C（DB9）]USB接口（2.0全速）以太网接口（10/100Base-T）USB接口（2.0全速）+蓝牙（2.0/2.1+EDR）USB接口，用户定义字符并将汉字放大1~8倍打印
可调整字符行距注：
纸轴内径为Φ12 mm，纸轴外径为Φ18 mm。注：1.出厂时仅提供一个数据接口。2.请以具体接口为标准。注：说明均在实验室测量下，使用指定纸张。TP830用户手册-39-点图像打印命令：支持不同密度的点图像和下载图像打印，可以省电保存NV位图（可以长时间保存LOGO）线性条码：UPC-A、UPC-E、EAN-13、EAN-8、CODE39、条码CODE128、ITF-25、CODABAR二维码：PDF417、，QR码电压：100~240 V（AC）IN频率：50Hz/60Hz电压：24 V（DC）电源（AC适配器）OUT电流：2.5 A温度：5~35℃工作环境湿度：25~80%RH（无冷凝）温度：-40~55℃环境条件储存环境湿度：≤93%RH（40℃，无冷凝）重量约1.45 kg噪音＜38 dB（A）（ISO7779标准）物理尺寸142 mm（宽）×195 mm（深）×132 mm（高）功耗① 工作：40 W；② 待机：大约3.5 W代码页76种控制面板1个键和3个LED纸型热敏卷纸注：本用户手册中的所有技术说明均为在国家标准的存储和工作环境（室温）下进行的实验室测量，测量纸符合本用户手册的规范。注意：为了确保打印机的使用寿命，严禁打印超过2CM的全线和全黑。
Paper installation
Pull out a small amount of paper, place it as shown, and close the front cover. Fig. 4-4 Pull out the paper Note: After the paper installation is completed, if the paper out LED and ERROR LED are still on, or the printer makes strange noises when feeding paper, please open the cover and close it tightly again. Correct the wrong paper roll Figure 4-3 Paper loading direction Note: The paper head should be placed downward and pulled toward the paper feed slot, but not the opposite. Roll paper TP830 User's Manual - 38 - Chapter 5, Specification 5.1, General specification, Item description, Printing method, hot wire printing, paper feeding mode, one-way friction feeding, paper ejecting direction, ejecting point density from the front 640 points/line (203 × 203 DPI) maximum print width: 80 mm, maximum 640 dot print speed: 300 mm/s maximum paper feed speed: 30 mm/s maximum line spacing 3.75 mm print head life 150 km, 1X108 pulse cutter life 1.5 million paper cutting thickness 0.065~0.14 mm TF50KS-E (Japan Paper Corporation) hot roll paper model AF50KS-E (JUJO Thermal) width: 79.5 ± 0.5 mm; 69.5 ± 0.5 mm; 57.5 ± 0.5 mm Weight: 53 ～ 80 g/m2 Maximum diameter: Φ 83 mm Paper thickness: 0.065 ～ 0.14 mm Paper specification Character set ASCII: 13 international character set interfaces This printer can be equipped with the following interfaces: parallel interface: Centronics USB interface: 2.0 full speed USB interface (2.0 full speed)+serial interface [RS-232C (DB9)] USB interface (2.0 full speed) Ethernet interface (10/100Base-T) USB interface (2.0 full speed)+Bluetooth (2.0/2.1+EDR) USB interface, user defined characters and printed Chinese characters by 1~8 times
Adjustable character line spacing Note:
The inner diameter of the paper shaft is Φ 12 mm, outside diameter of paper shaft Φ 18 mm。 Note: 1. Only one data interface is provided at the factory. 2. Please take the specific interface as the standard. Note: The instructions are all measured in the laboratory, using the specified paper. TP830 User's Manual - 39 - Point image printing command: supports point images of different densities and downloading image printing, and saves NV bitmaps (LOGO can be saved for a long time). Linear barcodes: UPC-A, UPC-E, EAN-13, EAN-8, CODE39, barcode CODE128, ITF-25, CODABAR QR code: PDF417, QR code Voltage: 100~240 V (AC) IN Frequency: 50Hz/60Hz Voltage: 24 V (DC) Power supply (AC adapter) OUT Current: 2.5 A Temperature: 5~35 ℃ Operating environment Humidity: 25~80% RH (non condensing) Temperature: - 40~55 ℃ Environmental conditions Storage environment Humidity: ≤ 93% RH (40 ℃, non condensing) Weight: about 1.45 kg Noise<38 dB (A) (ISO7779 standard) Physical size 142 mm (width) × 195 mm deep × 132 mm (high) power consumption ① Operation: 40 W; ② Standby: About 3.5 W code page, 76 control panels, 1 key and 3 LED paper thermal rolls Note: All technical descriptions in this user manual are laboratory measurements conducted under the national standard storage and working environment (room temperature), and the measuring paper conforms to the specifications in this user manual. Note: In order to ensure the service life of the printer, it is strictly prohibited to print all lines and all blackouts exceeding 2cm.
