AO820模拟量输出模块
显示了当前无线网络的IP地址信息
请根据此IP地址找出相应的无线网段，并在同一网段中设置具有不同IP地址的打印机IP。在图11中，IP地址为192.168.43.120，段为192.188.43。请不要直接在“打印机IP”项中填写此IP地址。在“打印机IP”项中，您应填写：192.168.43.x（1子网掩码设置打印机Wi-Fi接口的子网掩码。建议子网掩码应与无线网络相同。（检查图11中的子网屏蔽）打印机端口设置打印机Wi-Fi接口的端口号。建议使用9100。远程IP允许打印机接收目标IP（或IP段）发送的打印数据。根据您在图11.5中找到的无线网络IP地址填写相应的段。单击“保存”保存设置的参数，然后重新启动打印机。2.8.3检查Wi-Fi参数设置Wi-Fi网络参数后，应检查参数以确保Wi-Fi连接正确。1.通过“ping”命令检查打印机是否连接到网络。2.当“WLAN类型”选择为“基础设施”时，您可以查看Wi-Fi指示灯来判断连接状态。图11 TP830用户手册-25-LED说明2.9安装打印机网络驱动程序根据PC是否安装了打印机驱动程序，网络驱动程序的安装方式分为新安装方式和升级安装方式。如果PC上尚未安装打印机驱动程序，请采用新的安装方式，其步骤如“新安装打印机网络驱动程序”所示。如果PC上已安装打印机驱动程序，请采用升级安装方式，其步骤如“升级安装打印机网络驱动程序”所示。
升级安装打印机网络驱动程序
1.新安装打印机网络驱动程序1）单击“开始”→ “设置”→ “选择打印机”。2） 单击“添加打印机”，然后弹出“添加打印机向导”窗口，单击“下一步”。3） 弹出“添加打印机向导”窗口，在“本地或网络打印机”窗口中选择“本地打印机”，然后单击“下一步”。4） 弹出“选择打印机端口”窗口，选择“创建新端口”，然后在端口中选择“标准TCP/IP端口”并单击“下一步”。5） 弹出“添加标准TCP/IP打印机端口向导”窗口，单击“下一步”。6） 弹出“添加端口”窗口，在“打印机名称或IP地址”列中输入“设置打印机的IP地址”报告的IP地址。以IP地址“192.168.0.240”为例，如下图所示。填写完IP地址后，会自动创建“端口名”。Infrastructure Ad Hoc OFF Connect ON BLINK Disconnect BLINK ON BLINK Light Network WLAN type TP830 User’s Manual（基础设施自组织关闭连接打开BLINK断开BLINK光网络WLAN类型TP830用户手册）-26-7）弹出“Additional Port Information Required（所需附加端口信息）”窗口，在“Device type（设备类型）”中选择“Cu。8） 弹出“端口设置”窗口。确认“端口名”和“打印机名或IP地址”正确，“协议”为“RAW”，“端口号”为“9100”，单击“确定”。TP830用户手册-27-9）返回“所需附加端口信息”，单击“下一步”。10） 弹出“完成添加标准TCP/IP打印机端口向导”窗口，单击“完成”。11） 在“安装打印机软件”选项中，单击“从磁盘上安装”，然后单击“下一步”。12） 弹出“从磁盘安装”窗口。请根据操作系统环境，如Windows 2000/XP/Vista/Win7操作系统，选择如下路径：CD-ROM→ “驱动程序”→ “WIN2000（XP-Vista-Win7）”，单击“打开”，然后单击“确定”返回“安装打印机软件”窗口，单击“下一步”。13） 按照指南逐步单击“下一步”，直到安装完成。此时，打印机网络驱动程序已完全安装。2.升级安装打印机网络驱动程序（设置驱动程序的网络端口）如果PC已安装打印机驱动程序，请设置驱动程序网络端口以执行网络打印。具体步骤如下：1）点击“开始”→ “设置”→ “选择打印机”。2） 右键单击TP830驱动程序，在弹出的窗口中单击“属性”。3） 弹出“属性”窗口，单击“端口”和“添加端口”
Displays the IP address information of the current wireless network
Please find out the corresponding wireless network segment according to this IP address, and set the printer IP with different IP addresses in the same network segment. In Figure 11, the IP address is 192.168.43.120, and the segment is 192.188.43. Please do not fill in this IP address directly in the "Printer IP" item. In the "Printer IP" item, you should fill in: 192.168.43. x (1 subnet mask sets the subnet mask of the printer's Wi Fi interface. It is recommended that the subnet mask should be the same as the wireless network. (Check the subnet mask in Figure 11) The printer port sets the port number of the printer's Wi Fi interface. 9100 is recommended. Remote IP allows the printer to receive print data sent by the target IP (or IP segment). Fill in the corresponding section according to the wireless network IP address you find in Figure 11.5. Click Save to save the set parameters, and then restart the printer. 2.8.3 Check the Wi Fi parameters After setting the Wi Fi network parameters, check the parameters to ensure that the Wi Fi connection is correct. 1. Check whether the printer is connected to the network through the "ping" command. 2. When "WLAN Type" is selected as "Infrastructure", you can check the Wi Fi indicator to determine the connection status. Figure 11 TP830 User Manual - 25-LED Description 2.9 Installing the printer network driver. According to whether the PC has installed the printer driver, the installation mode of the network driver can be divided into new installation mode and upgrade installation mode. If the printer driver has not been installed on the PC, please use a new installation method. The steps are shown in "Installing a new printer network driver". If the printer driver has been installed on the PC, please use the upgrade installation method. The steps are shown in "Upgrading and installing the printer network driver".
Upgrade and install the printer network driver
1. Install the printer network driver 1) Click Start → Settings → Select Printer. 2) Click Add Printer, and then the Add Printer Wizard window pops up. Click Next. 3) The Add Printer Wizard window pops up. Select Local Printer in the Local or Network Printer window, and then click Next. 4) The Select Printer Port window pops up, select Create New Port, then select Standard TCP/IP Port in the port and click Next. 5) The Add Standard TCP/IP Printer Port Wizard window pops up, and click Next. 6) Pop up the "Add Port" window, and enter the IP address of the "Set Printer IP Address" report in the "Printer Name or IP Address" column. Take the IP address "192.168.0.240" as an example, as shown in the following figure. After filling in the IP address, the "Port Name" will be automatically created. Infrastructure Ad Hoc OFF Connect ON BLINK Disconnect BLINK ON BLINK Light Network WLAN type TP830 User's Manual - 26-7) The "Additional Port Information Required" window pops up, and select "Cu" in the "Device type". 8) The "Port Settings" window pops up. Confirm that the Port Name and Printer Name or IP Address are correct, the Protocol is RAW, and the Port Number is 9100. Click OK. TP830 User Manual-27-9) Return to "Additional Port Information Required" and click "Next". 10) The window "Completing the Add Standard TCP/IP Printer Port Wizard" pops up, and click "Finish". 11) In the Install Printer Software option, click Install from Disk, and then click Next. 12) The Install from Disk window pops up. Please select the following path according to the operating system environment, such as Windows 2000/XP/Vista/Win7 operating system: CD-ROM → Driver → WIN2000 (XP Vista Win7), click Open, click OK to return to the Install Printer Software window, and click Next. 13) Follow the guide step by step to click Next until the installation is complete. The printer network driver is now fully installed. 2. Upgrade and install the printer network driver (set the network port of the driver) If the PC has installed the printer driver, set the driver network port to perform network printing. The specific steps are as follows: 1) Click Start → Settings → Select Printer. 2) Right click the TP830 driver and click Properties in the pop-up window. 3) Pop up the "Properties" window, click "Port" and "Add Port"
