AO801工控备件
连接并行接口电缆
1.确保计算机和打印机都已关闭，将并行电缆插入打印机的并行接口，挤压两侧的线夹并固定电缆。如图2-3.2所示。将电缆的另一端插入计算机。拧紧两侧的螺钉并固定电缆。2.3.3连接USB接口电缆1.将USB电缆A端（扁平）插入计算机的USB接口。2.将USB电缆B端（方形）插入打印机的USB接口，如图2-4所示。图2-3连接并行接口电缆图2-2连接现金抽屉电缆注意：请使用合适的现金抽屉。当使用未经授权的现金抽屉时，制造商将不履行保修。注意：连接USB接口电缆后，请勿撞击插头。现金抽屉接口现金抽屉电缆并行接口线夹并行接口电缆TP830用户手册-5-2.3.4连接串行接口电缆1.确保计算机和打印机都已关闭，将串行电缆插入打印机的串行接口。拧紧两侧的螺钉并固定电缆。如图2-5.2所示。将电缆的另一端插入计算机的串行接口。拧紧两侧的螺钉并固定电缆2.3.5连接以太网接口电缆1.将以太网电缆（RJ-45）的水晶端插入打印机的以太网接口，另一端插入LAN。（如图2-6所示）图2-5连接串行接口电缆图2-4连接USB接口电缆图6-6连接以太网接口电缆USB接口USB接口电缆螺钉串行接口电缆串行接口以太网接口以太网接口电缆TP830用户手册-6-2.4
连接电源线
1。确保打印机已关闭。（开关上带有“O”标记的按下侧表示打印机已关闭）2.确保电源插座的电压与打印机的电压匹配。3.将交流适配器插入打印机的电源插座。4.将电源线的一端插入交流适配器，然后将电源线另一端插入接地电源插座。2.5安装打印机驱动程序和选择切割器在使用TP830打印机之前，应在Windows中设置打印机驱动程序。请使用电缆将计算机与打印机连接起来，然后打开计算机和打印机，将驱动程序CD放入CD-ROM中。按照以下方式安装驱动程序：自动安装方式双击驱动程序光盘中的文件“Setup.exe”，按照以下指南安装驱动程序。手动安装方式图2-7连接电源线警告：1.如果额定电压与插座电压不匹配，请联系经销商寻求帮助。请勿插入电源线。2.请正确使用接地插座。3.请仅使用原装交流适配器。当使用未经授权的交流适配器时，制造商将不履行保修。注意：自动安装方式需要Windows 2000及以上的操作系统，不支持Windows 98/ME及以下的操作系统。注意：有关网络设置的详细说明，请参阅用户手册。电源线交流适配器电源插座注：串行接口和并行接口的手动安装方式相同。
Connecting the Parallel Interface Cable
1. Make sure that the computer and printer are turned off, insert the parallel cable into the parallel interface of the printer, squeeze the clamps on both sides and fix the cable. As shown in Fig. 2-3.2. Plug the other end of the cable into the computer. Tighten the screws on both sides and secure the cable. 2.3.3 Connect the USB interface cable 1. Plug the A end (flat) of the USB cable into the USB interface of the computer. 2. Insert the B end (square) of the USB cable into the USB interface of the printer, as shown in Figure 2-4. Figure 2-3 Connecting the Parallel Interface Cable Figure 2-2 Connecting the Cash Drawer Cable Note: Please use a suitable cash drawer. When unauthorized cash drawers are used, the manufacturer will not perform the warranty. Note: After connecting the USB interface cable, do not hit the plug. Cash drawer interface Cash drawer cable Parallel interface cable clamp Parallel interface cable TP830 User's Manual - 5-2.3.4 Connect the serial interface cable 1. Make sure that the computer and printer are turned off, and plug the serial cable into the serial interface of the printer. Tighten the screws on both sides and secure the cable. As shown in Figure 2-5.2. Plug the other end of the cable into the serial interface of the computer. Tighten the screws on both sides and fix the cable 2.3.5 Connect the Ethernet interface cable 1. Insert the crystal end of the Ethernet cable (RJ-45) into the Ethernet interface of the printer and the other end into the LAN. (As shown in Fig. 2-6) Fig. 2-5 Connecting the Serial Interface Cable Fig. 2-4 Connecting the USB Interface Cable Fig. 6-6 Connecting the Ethernet Interface Cable USB Interface Cable Screw Serial Interface Cable Serial Interface Ethernet Interface Cable TP830 User's Manual - 6-2.4
Connecting the power cord
1。 Make sure the printer is turned off. (The lower side of the switch marked with "O" indicates that the printer is turned off.) 2. Make sure that the voltage of the power socket matches the voltage of the printer. 3. Plug the AC adapter into the printer's power outlet. 4. Plug one end of the power cord into the AC adapter, and then plug the other end of the power cord into a grounded power outlet. 2.5 Installing the printer driver and selecting the cutter Before using the TP830 printer, the printer driver should be set in Windows. Use the cable to connect the computer to the printer, then turn on the computer and printer, and place the driver CD in the CD-ROM. Install the driver in the following way: Automatic installation method Double click the file "Setup. exe" on the driver CD, and install the driver according to the following guidelines. Manual installation method Figure 2-7 Connecting power cord Warning: 1. If the rated voltage does not match the socket voltage, please contact the dealer for help. Do not plug in the power cord. 2. Please use the grounding socket correctly. 3. Please only use the original AC adapter. The manufacturer will not perform the warranty when using an unauthorized AC adapter. Note: The automatic installation mode requires Windows 2000 and above operating systems, but does not support Windows 98/ME and below operating systems. Note: For detailed instructions on network settings, refer to the user manual. Power cord AC adapter power socket Note: The manual installation method of serial interface and parallel interface is the same.
