AI830工控备件
简洁而简单的设计
确保您的焊工能够连续生产。如果出现问题，SOLUTION®的自诊断功能，加上仅有两块电路板，可让工厂人员在几分钟内将焊机重新投入生产。无需布线，只需插入并开始焊接即可。PROFIT RSW UNITROL SOLUTION®提供独特的选项：软触安全系统保护焊工免受电极夹点伤害。无法击败或绕过。焊尖力监测使用固态差压传感器或称重传感器监测焊接力。每次焊接都会在同一精确点自动开始，以消除挤压时间的需要。此选项还检查每个焊接结束时的TIP FORCE，以确保其保持在客户设置的窗口内。恒定焊接电流全闭环反馈系统维持焊接电流。此选项允许在实际AMPS中设置焊接程序，以消除试验和错误设置。还包括电流监控功能，用于拒绝超出范围的焊接。电子压力调节器自动设置空气压力以匹配所需的电极力。消除了手动设置和调整。打印机/通信端口RS-232或RS-485串行端口，用于捕获焊接电流、电极力、线电压和故障指示器。
可连接到外部打印机或PC
UNITROL SOLUTION®适合所有人。UNITTROL SOLUTION®有助于解决四大焊接问题：操作特点软触摸安全系统保护操作员免受夹点伤害。*微机控制系统以最少的部件提供最大的灵活性。工厂编程软件，用于处理所有焊接功能——现在和将来。75每个程序中具有所有RWMA完整功能的焊接计划存储器。自动电压补偿（AVC）确保焊机输出一致。这将焊机输出保持在±1%，输入线电压变化为±10%。电子计数器自动显示焊接完成或焊接完成的零件。节水器电路，用于驱动115伏电磁阀，在更换喷嘴时节约用水并保护操作员。叶尖压力计算自动计算所需叶尖力的压力调节器设置。双级启动：A级关闭尖端，B级开始焊接。用于双手按钮的防系紧装置。脚或手开关操作的自动检测。双重计划：将75个焊接程序中的任意两个分配给两个不同的启动输入。正负前半周点火，键盘可选择。
Simple and simple design
Make sure your welder can produce continuously. If there is a problem, SOLUTION ® The self diagnosis function of, plus only two circuit boards, allows factory personnel to put the welding machine back into production in a few minutes. No wiring is required, just insert and start welding. PROFIT RSW UNITROL SOLUTION ® Unique option: Soft touch safety system to protect welders from electrode pinch points. Unable to defeat or bypass. Welding tip force monitoring uses solid differential pressure sensor or load cell to monitor welding force. Each welding will automatically start at the same precise point to eliminate the need for extrusion time. This option also checks the TIP FORCE at the end of each weld to ensure that it remains within the window set by the customer. The full closed loop feedback system of constant welding current maintains the welding current. This option allows the welding procedure to be set in the actual AMPS to eliminate tests and false settings. It also includes a current monitoring function to reject out of range welding. The electronic pressure regulator automatically sets the air pressure to match the required electrode force. Eliminates manual settings and adjustments. Printer/communication port RS-232 or RS-485 serial port for capturing welding current, electric force, line voltage and fault indicator.
Can be connected to an external printer or PC
UNITROL SOLUTION ® For everyone. UNITTROL SOLUTION ® It helps to solve the four major welding problems: operating characteristics The soft touch safety system protects the operator from pinch points* The microcomputer control system provides maximum flexibility with minimum components. Factory programming software to handle all welding functions - now and in the future. 75 Welding plan memory with all RWMA complete functions in each program. Automatic voltage compensation (AVC) ensures consistent output of the welding machine. This keeps the output of the welder at ± 1% and the input line voltage changes by ± 10%. The electronic counter automatically displays the parts that have been welded or have been welded. The water saver circuit is used to drive the 115 volt solenoid valve to save water and protect the operator when changing the nozzle. Tip pressure calculation automatically calculates the pressure regulator settings for the required tip force. Two stage startup: Level A closes the tip and Level B starts welding. Anti tie down device for two handed buttons. Automatic detection of foot or hand switch operation. Dual plan: any two of the 75 welding programs are assigned to two different start inputs. Positive and negative ignition in the first half cycle, keyboard selectable.
