ACS580-01-07A3-4模拟量输出模块
系统800xA硬件
选择器数据表模拟输入模块有8个通道。每个通道可以是电压或电流输入。电流互感器能够在不损坏的情况下处理至少30 V直流电对变送器电源的短路。限流由PTC电阻器执行。电流互感器的输入电阻为250欧姆，包括PTC。电压输入能够承受至少30 V直流的过压或欠压。输入电阻为290k欧姆。变送器电源可连接至L1+、L1-和/或L2+、L2-。特点和优点8通道，用于0…20 mA、4…20 mA，0…10 V或2…10 V直流，单端单极输入1组8通道，与地隔离12位分辨率输入分流电阻器，由PTC电阻器保护至30 V。模拟输入短路至ZP或+24 V。输入耐受HART通信。一般信息类型模拟输入信号规格0..20mA、4..20mA、0..10V，2..10V产品编号3BSE008516R1通道数8信号类型单极单端HART无SOE无冗余无高完整性无本质安全无机械S800数据表 | 2019-05-15 |版权所有©2019
ABB 1详细数据分辨率
12位输入阻抗290 kΩ（电压输入）230-275 kΩ（电流输入）隔离按组与地隔离低于/高于范围-5%/+15%最大误差0.1%温度漂移电压：典型值。最大70 ppm/°C。100 ppm/°C；电流：类型。50 ppm/°C最大值。80 ppm/°C输入滤波器（上升时间0-90%）140ms更新周期时间8ms限流变送器功率可由MTU限流最大现场电缆长度600米（656码）最大输入电压（非破坏性）30 V直流NMRR，50Hz，60Hz>40 dB额定绝缘电压50 V介电测试电压500 V交流。功耗1.5 W电流消耗+5 V模块总线70mA电流消耗+24 V模块总线40mA电流消耗+24 V外部0诊断前LED的F（故障）、R（未）、W（警告）监控内部电源监控状态指示模块错误、模块警告、通道错误环境和认证CE标志是电气安全IEC 61131-2，UL 508危险位置C1 Div 2 cULus、C1 Zone 2 cULus、ATEX Zone 2 Marine认证ABS、BV、DNV-GL、LR、RS、CCS防护等级IP20
System 800xA hardware
The selector data table analog input module has 8 channels. Each channel can be a voltage or current input. The current transformer shall be able to handle at least 30 V DC short circuit to the transmitter power supply without damage. Current limiting is performed by PTC resistors. The input resistance of current transformer is 250 ohms, including PTC. The voltage input can withstand overvoltage or undervoltage of at least 30 V DC. The input resistance is 290k ohms. The transmitter power supply can be connected to L1+, L1 - and/or L2+, L2 -. Features and advantages 8 channels, used for 0... 20 mA, 4... 20 mA, 0... 10 V or 2... 10 V DC, single ended single pole input 1 group of 8 channels, isolated from the ground with 12 bit resolution input shunt resistor, protected to 30 V by PTC resistor. The analog input is shorted to ZP or+24 V. Input withstands HART communication. General information type Analog input signal specification 0.. 20mA, 4.. 20mA, 0.. 10V, 2.. 10V Product No. 3BSE008516R1 Number of channels 8 Signal type Single pole single ended HART No SOE No redundancy No high integrity No intrinsic safety No mechanical S800 data sheet | 2019-05-15 | All rights reserved © two thousand and nineteen
ABB 1 detailed data resolution
The 12 bit input impedance 290 k Ω (voltage input) 230-275 k Ω (current input) is isolated from the ground by group. The isolation is lower/higher than the range - 5%/+15%. The maximum error is 0.1%. Temperature drift voltage: typical value. 70 ppm/° C max. 100 ppm/°C； Current: Type. 50 ppm/° C max. 80 ppm/° C input filter (rise time 0-90%) 140ms Update cycle time 8ms Current limiting transmitter power can be limited by MTU Maximum field cable length 600m (656 yards) Maximum input voltage (non-destructive) 30 V DC NMRR, 50Hz, 60Hz>40 dB Rated insulation voltage 50 V Dielectric test voltage 500 V AC. Power consumption 1.5 W current consumption+5 V module bus 70 mA current consumption+24 V module bus 40 mA current consumption+24 V external 0 LED F (failure), R (failure), W (warning) monitoring internal power monitoring status indication module error, module warning, channel error environment and certification CE mark is electrical safety IEC 61131-2, UL 508 hazardous location C1 Div 2 cULus, C1 Zone 2 cULus, ATEX Zone 2 Marine certification ABS, BV, DNV-GL, LR, RS CCS protection grade IP20
