81EU01E-E PLC/DCS系统模块
通过菜单命令
“文件-打印”，您可以在屏幕上打印程序。如果有一个驱动器连接到您的电脑硬件，您可以通过菜单命令drive-Connect（如果有多个驱动器连接至电脑硬件，则可以从可用驱动器列表中选择该驱动器）与该驱动器进行软件连接。注意：如果在连接DriveAP时更改驱动器语言，则必须关闭和打开驱动器电源，然后重新连接。此连接命令将DriveAP的操作模式更改为离线模式。通过菜单命令Drive-Upload，您可以上传并显示连接驱动器的AP程序。如果光标位于块上，并按F3键，则该块的描述将显示在“信息”窗口中。如果需要，现在可以修改屏幕上的AP程序（参见本章中的“程序修改”一节）。通过菜单命令File-Download，您可以将屏幕上的程序下载到连接的驱动器。除了上述用于上传和下载的菜单命令外，文件菜单中的命令在此操作模式下可用。如果您想使用另一个连接到电脑的驱动器，请先通过菜单命令drive-disconnect断开当前连接的驱动器，然后通过菜单命令drive-Connect by菜单命令drive-On Line连接到新的驱动器。如果您将DriveAP的操作模式更改为On Lin mode（联机模式）。
启动期间
注：在该操作模式启动期间，连接驱动器的AP程序会自动上传并显示。如果光标位于块上，并按F3键，则该块的描述将显示在“信息”窗口中。在此模式下对屏幕上程序的所有修改（参见本章程序修改一节）将自动复制到连接的驱动器脱机模式联机模式使用DriveAP DriveAP用户手册3-5注意：在线模式下，请勿通过面板（或其他方式）更改AP参数值，因为这些更改不会显示在屏幕上！如果一个参数（或一个参数的一部分）连接到块的输入引脚，并且您在按住Shift键的同时单击该输入引脚（或任何输出引脚），则该参数（或该输出引脚）的实际值将实时以数字方式显示在屏幕上。注意：如果您有DriveWindow，并且启用了DriveWindow+DriveAP的同时使用，则可以在DriveAP运行时使用DriveWindows以图形方式监视参数值。通过再次单击（同时按住Shift键）同一引脚，可以删除值显示。标准用户界面：连接驱动器中AP程序的状态（运行、停止或编辑）显示在屏幕上，可以通过菜单命令“驱动器-启动”、“驱动器-停止”和“驱动器-编辑”更改。高级用户界面：已连接驱动器中当前可见时间级别（运行、停止或编辑）的状态显示在屏幕上，可以通过菜单命令“驱动器-启动此时间级别”、“驱动器-停止此时间级别和“驱动器-编辑此时间级”进行更改。所有时间级别的状态可以通过菜单命令Drive-Start all time levels、Drive-Stop all time levels和Drive-Edit all TimeLevels更改。连接的驱动器的状态信息实时显示在屏幕上的“驱动器状态”框中。通过在按住Shift键的同时单击参考值显示，可以删除参考值显示。标准用户界面：所有非AP参数的列表显示在功能块下方的列表框中。高级用户界面：参数窗口列出所有非AP参数。如果删除此窗口，您可以通过按F2键（或通过菜单命令“驱动器-参数列表-显示参数列表”）再次看到它。参数列表中所有参数的当前值都可以通过菜单命令驱动器-参数列表-上传值从驱动器中读取（通过单击列表中的该参数可以读取参数的当前数值）。双击列表中所需的参数，可以更改驱动器中非AP参数的值。
By menu command
"File - Print", you can print the program on the screen. If there is a drive connected to your computer hardware, you can connect it to the software through the menu command drive Connect (if there are multiple drives connected to your computer hardware, you can select the drive from the list of available drives). Note: If you change the drive language while connecting DriveAP, you must turn the drive power off and on, and then reconnect it. This connection command changes the operation mode of DriveAP to offline mode. With the menu command Drive Load, you can upload and display the AP program connected to the drive. If the cursor is over a block and you press F3, the description of the block is displayed in the Information window. If necessary, you can now modify the AP program on the screen (see the "Program Modification" section in this chapter). You can download the program on the screen to the connected drive through the menu command File Download. In addition to the above menu commands for uploading and downloading, the commands in the file menu are available in this operation mode. If you want to use another drive connected to the computer, first disconnect the currently connected drive through the menu command drive disconnect, and then connect to the new drive through the menu command drive Connect by menu command drive On Line. If you change the operation mode of the DriveAP to On Lin mode.
During start-up
Note: During the startup of this operation mode, the AP program connected to the drive will be uploaded and displayed automatically. If the cursor is over a block and you press F3, the description of the block is displayed in the Information window. All modifications to the programs on the screen in this mode (see the program modification section in this chapter) will be automatically copied to the connected drive Offline mode Online mode Use DriveAP DriveAP User's Manual 3-5 Note: In online mode, do not change the AP parameter values through the panel (or other methods), because these changes will not be displayed on the screen! If a parameter (or part of a parameter) is connected to the input pin of the block, and you click the input pin (or any output pin) while holding down the Shift key, the actual value of the parameter (or the output pin) will be displayed on the screen in a digital way in real time. Note: If you have a DriveWindow and you enable DriveWindow+DriveAP to be used at the same time, you can use DriveWindows to monitor parameter values graphically when DriveAP is running. You can delete the value display by clicking the same pin again (while holding down the Shift key). Standard user interface: The status (running, stopping or editing) of the AP program in the connected drive is displayed on the screen and can be changed through the menu commands "Drive Start", "Drive Stop" and "Drive Edit". Advanced user interface: The status of the currently visible time level (running, stopping, or editing) in the connected drive is displayed on the screen. You can change it through the menu commands "Drive - Start this time level", "Drive - Stop this time level", and "Drive - Edit this time level". The status of all time levels can be changed through the menu commands Drive Start all time levels, Drive Stop all time levels, and Drive Edit all TimeLevels. The status information of the connected drive is displayed in the "Drive Status" box on the screen in real time. You can delete the reference value display by holding down the Shift key while clicking the reference value display. Standard user interface: The list of all non AP parameters is displayed in the list box below the function block. Advanced user interface: The parameter window lists all non AP parameters. If you delete this window, you can see it again by pressing F2 (or through the menu command "Drive - Parameter List - Display Parameter List"). The current values of all parameters in the parameter list can be read from the drive through the menu command Drive - Parameter List - Upload Value (click the parameter in the list to read the current value of the parameter). Double click the required parameter in the list to change the value of non AP parameter in the drive.
