5SHY3545L0010 3BHB013088R0001工控模块卡件
使用本数据表
本数据表总结了有关块安装、配置和诊断的信息。您的主要参考应为《离散和模拟块用户手册》。它包括块安装和配置的详细说明。有关系统和通信的更多信息，包括总线规格，请参阅I/O系统和通信手册。兼容性 配置需要IC66*HHM501E（3.7版）或更高版本的手持监视器。对于IC697系列PLC，如果CPU型号为IC697CPU731，则必须为G或更高版本。如果是型号IC697CPU771，则必须是版本E或更高版本。编程软件必须为2.02或更高版本。需要总线控制器IC697BEM731C或更高版本。对于IC600系列PLC，CPU必须为105或更高版本。对于IC600系列“Plus”PLC，需要110版或更高版本。编程软件必须为4.02或更高版本。对于IC550系列PLC，CPU必须为3.0版或更高版本。编程软件必须为2.01或更高版本。如果总线开关模块将直接连接到模块，则必须为24/48 VDC版本（IC66*BSM021）。安装说明 仔细检查所有装运集装箱是否损坏。如果任何设备损坏，请立即通知送货服务。保存损坏的运输集装箱，以供送货服务部门检查。设备开箱后，记录所有序列号。保存装运集装箱和包装材料，以防需要运输或装运系统的任何部分。块安装Genius I/O块被视为“开放设备”，因此必须安装在保护外壳内。它们应位于清洁且无空气污染物的区域。应有足够的冷却气流。该块可以安装在正上方，也可以倒置。在块之间留出至少2英寸的空间。通过为8-32硬件钻两个螺钉或螺栓孔来安装缸体。
螺钉安装块
定位块，使上下法兰上的槽口与安装孔对齐。使用8-32个螺钉安装块。使用星形垫圈提供接地完整性。接地块的安装螺钉不得用作块接地的唯一方式。使用最小尺寸AWG#12（横截面平均3.3mm2）的短导线将块上的绿色接地螺钉连接到可靠的接地系统。警告：如果安装螺钉没有良好的接地连接，并且接地螺钉没有连接到可靠的接地，则块没有接地。存在触电危险。可能导致死亡或人身伤害。接线盒 请勿过度拧紧端子螺钉。所有端子的推荐扭矩为6 in/lb（.678 N/M）。串行总线接线端子1至4用于串行总线。这些端子接受一根AWG#12导线（平均横截面为3.3mm2）或两根AWG#14导线（每根平均横截面2.1mm2）。建议的最小导线尺寸为AWG#22（横截面平均36mm2）。端子1-4还可容纳宽达0.27英寸（6.85mm）的铲形或环形端子，6号螺钉的最小开口，从螺钉中心到后挡板的深度可达0.20英寸（5.1mm）。确保非屏蔽线端不超过2英寸（5厘米）。使用系统和通信用户手册中推荐的电缆类型之一，将串行总线连接到端子1-4。（如果模块将控制总线开关模块，请参见下文。）1 2 3 4串行1串行2屏蔽输入屏蔽输出如果模块位于总线的任一端，在其串行1和串行2端子上连接适当类型的终端电阻器（有关详细信息，请参阅系统和通信用户手册）。串行1串行2屏蔽输入屏蔽输出总线终端电阻器串行1串行1屏蔽输入屏蔽输入输出终端电阻器连接总线开关模块如果总线开关模块将直接连接到模块，请将其连接到串行总线终端，如下一页所示。按照总线交换模块数据表中的说明，将串行总线电缆连接到BSM。将一根BSM尾光纤连接到端子9，另一根连接到端子10。
Use this data sheet
This data sheet summarizes information about block installation, configuration, and diagnostics. Your main reference should be the Discrete and Analog Block User's Manual. It includes detailed instructions for block installation and configuration. For more information about the system and communications, including bus specifications, refer to the I/O System and Communications manual. Compatibility configuration requires IC66 * HHM501E (version 3.7) or higher handheld monitor. For IC697 series PLC, if the CPU model is IC697CPU731, it must be G or higher. If it is model IC697CPU771, it must be version E or higher. The programming software must be 2.02 or higher. Bus Controller IC697BEM731C or later is required. For IC600 series PLC, the CPU must be 105 or higher. For IC600 series "Plus" PLC, version 110 or higher is required. The programming software must be 4.02 or later. For IC550 series PLC, the CPU must be version 3.0 or higher. The programming software must be 2.01 or higher. If the bus switch module will be connected directly to the module, it must be 24/48 VDC version (IC66 * BSM021). Installation instructions Carefully check all shipping containers for damage. If any equipment is damaged, please inform the delivery service immediately. Keep the damaged shipping container for inspection by the delivery service department. After unpacking the equipment, record all serial numbers. Keep shipping containers and packaging materials in case any part of the transportation or shipping system is required. Block mount Genius I/O blocks are considered "open devices" and must therefore be installed in a protective enclosure. They shall be located in a clean area free from air pollutants. There shall be sufficient cooling air flow. The block can be installed directly above or upside down. Leave at least 2 inches of space between the blocks. Install the cylinder block by drilling two screw or bolt holes for the 8-32 hardware.
Screw mounting block
Position the block so that the notches on the upper and lower flanges are aligned with the mounting holes. Use 8-32 screws to install the block. Use star washers to provide ground integrity. The mounting screws of the grounding block shall not be used as the only way to ground the block. Connect the green grounding screw on the block to the reliable grounding system with a short conductor with the minimum size of AWG # 12 (average cross section 3.3mm2). Warning: If the mounting screw is not well grounded and the grounding screw is not connected to a reliable grounding, the block is not grounded. There is a danger of electric shock. May cause death or personal injury. Do not overtighten the terminal screws of the terminal box. The recommended torque for all terminals is 6 in/lb (. 678 N/M). Serial bus terminals 1 to 4 are used for the serial bus. These terminals accept one AWG # 12 conductor (average cross section 3.3mm2) or two AWG # 14 conductors (average cross section 2.1mm2 each). The recommended minimum conductor size is AWG # 22 (average cross-section of 36mm2). Terminals 1-4 can also accommodate spade or ring terminals up to 0.27 inch (6.85 mm) wide. The minimum opening of No. 6 screw can be 0.20 inch (5.1 mm) deep from the screw center to the tailgate. Ensure that the unshielded wire end does not exceed 2 inches (5 cm). Connect the serial bus to terminals 1-4 using one of the cable types recommended in the system and communications user manual. (If the module will control the bus switch module, see below.) 1 2 3 4 Serial 1 Serial 2 Shielded Input Shielded Output If the module is located at either end of the bus, connect the appropriate type of terminating resistor to its Serial 1 and Serial 2 terminals (see the System and Communication User Manual for details). Serial 1 Serial 2 Shielded Input Shielded Output Bus Termination Resistor Serial 1 Serial 1 Shielded Input Shielded I/O Termination Resistor Connection Bus Switch Module If the bus switch module will be connected directly to the module, connect it to the serial bus terminal, as shown on the next page. Connect the serial bus cable to the BSM as described in the Bus Switching Module data sheet. Connect one BSM pigtail to terminal 9 and the other to terminal 10.
