5SHY3545L0009 3BHB013085R0001机器人卡件
说明 电流源模拟I/O块
用于将控制器连接到提供或接受4mA至20mA模拟信号的设备。有两种块版本可供选择：115 VAC电流源模拟I/O块（IC66*BBA104）24/48 VDC电流源模拟输入/输出块（IC66*BBA024）这些块除电源外均相同。GND H N NC-BSM OUT RTN GNN OUT RTN GND+BSM EXC IN COM GND EXC IN COMGND EXD IN COMGNDEXC IN CONGND电流源模拟输入/输出（115V 50/60 Hz或125VDC.25A Max）功能块功能包括：六个4至20 mA模拟电路：4个输入和2个输出隔离通道操作无需用户校准软件可配置高级诊断专用总线开关模块控制A电流源模拟I/O块有四个4至20mA电流输入。每个输入提供一个24伏电流回路电源，并与模块内的所有其他电路隔离。两个输出通道提供两个4至20mA电流回路的电源和控制。输出通道和BSM电路在电气上是共用的，但与输入隔离。块上的所有电路都支持独立选择线性缩放值。这些值可用于将内部值转换为适合应用的工程单位。块诊断包括：输入低和高报警检测输入和输出的超范围和欠范围检测输入开路检测输出反馈错误检测内部故障报告提供专用数字输出以驱动总线开关模块（仅限版本IC66*BSM021）。
电流源模拟I/O块
IC66*BBA104端子组件IC66*TBA104电子组件IC66*EBA104 24/48 VDC电流源输入/输出块IC66*BBA024端子组件IC66*TBA024电子组件IC66*EBA024块规格尺寸（高x宽x深）8.83“（22.44cm）x 3.34”（8.48cm）x3.91“（9.93cm）重量4 lbs.（1.8 kg）LED（I/O块）单元正常，I/O启用块到块隔离1500V一分钟组到组隔离1500VRMS散热12瓦最大BSM控制开关一个24/48 VDC BSM（IC66*BSM021）块功率（标称）；115VAC 125VDC 24/48VDC电源电压最大电流频率/纹波PS下降时间98-132 VAC 250mA 47-63 Hz 1周期105-145 VDC 140mA 10%最大纹波10 ms最小18-56 600mA 10%最大波纹10 ms最小。输入规格输入精度（25°C时）满量程读数的0.1%*输入分辨率1µA输入转换时间16.6ms至400ms（用户可选）范围4mA至20mA超量程容量0mA至25mA输入诊断欠/超量程、高/低报警，开路信道到信道隔离1500V rms热漂移（从25°C）70 PPM每°C典型输入阻抗100欧姆+/-5%正常模式抑制-50，60 Hz输入励磁：开路电压短路电流回路阻抗24VDC<75mA最大1000欧姆（0mA至20mA）最大800欧姆（20mA至25mA）输出规格25°C时的输出精度满量程读数的0.15%输出分辨率6µA输出更新频率6ms至8ms典型范围4mA至20mA超量程容量0mA至24mA输出诊断欠量程、超量程、，反馈误差输出负载0欧姆至850欧姆热漂移（从25°C）35 PPM每摄氏度典型环境规范工作温度0°C至+60°C（+32°至+140°F）存储温度-40°至+100°C（-40°到+212°F）湿度5%至95%（非冷凝）振动5-10 Hz 0.2“（5.08mm）位移，1G下10-200 Hz参考GFK-0867B了解产品标准和一般规范。*在存在严重射频干扰（IEC 801-3，10 V/m）的情况下，精度可能会降低到满量程读数的+/-0.25%
Description Current source analog I/O pack
Used to connect the controller to a device that provides or receives 4mA to 20mA analog signals. Two block versions are available: 115 VAC current source analog I/O block (IC66 * BBA104) 24/48 VDC current source analog I/O block (IC66 * BBA024) These blocks are the same except for the power supply. GND H N NC-BSM OUT RTN GNN OUT RTN GND+BSM EXC IN COM GND EXC IN COMGND EXD IN COMGNDEXC IN CONGND Current source Analog input/output (115V 50/60 Hz or 125VDC. 25A Max) Function block includes: six 4 to 20 mA analog circuits: four inputs and two outputs Isolated channel operation without user calibration software Configurable advanced diagnosis dedicated bus switch module Control A Current source Analog I/O block has four 4 to 20 mA current inputs. Each input provides a 24 volt current loop power supply and is isolated from all other circuits within the module. Two output channels provide power and control for two 4 to 20mA current loops. The output channel and BSM circuit are electrically common, but isolated from the input. All circuits on the block support independent selection of linear scaling values. These values can be used to convert internal values to engineering units appropriate for the application. Block diagnosis includes: input low and high alarm detection input and output over range and under range detection input open circuit detection output feedback error detection internal fault report providing dedicated digital output to drive the bus switch module (version IC66 * BSM021 only).
Current source analog I/O pack
IC66 * BBA104 terminal assembly IC66 * TBA104 electronic assembly IC66 * EBA104 24/48 VDC current source input/output block IC66 * BBA024 terminal assembly IC66 * TBA024 electronic assembly IC66 * EBA024 block size (H x W x D) 8.83 "(22.44cm) x 3.34" (8.48cm) x 3.91 "(9.93cm) weight 4 lbs. (1.8 kg) LED (I/O block) The unit is normal. I/O is enabled. Block to block isolation 1500V for one minute. Group to group isolation 1500VRMS heatsink 12W. Maximum BSM control switch. One 24/48 VDC BSM (IC66 * BSM021) block power (nominal); 115VAC 125VDC 24/48VDC power supply voltage maximum current frequency/ripple PS drop time 98-132 VAC 250mA 47-63 Hz 1 cycle 105-145 VDC 140mA 10% maximum ripple 10 ms minimum 18-56 600mA 10% maximum ripple 10 ms minimum. Input specification Input accuracy (at 25 ° C) 0.1% of full scale reading * Input resolution 1 µ A Input conversion time 16.6ms to 400ms (user selectable) Range 4mA to 20mA Over range capacity 0mA to 25mA Input diagnosis under/over range, high/low alarm, Open circuit channel to channel isolation 1500V rms thermal drift (from 25 ° C) 70 PPM typical input impedance per ° C 100 ohms+/- 5% normal mode suppression - 50, 60 Hz input excitation: open circuit voltage short circuit current loop impedance 24VDC<75mA maximum 1000 ohms (0mA to 20mA) maximum 800 ohms (20mA to 25mA) Output specification 0.15% of full scale reading at 25 ° C Output resolution 6 µ A Output update frequency 6ms to 8ms Typical range 4mA to 20mA Over range capacity 0mA to 24mA Output diagnosis Under range, over range, Feedback error Output load 0 ohm to 850 ohm Thermal drift (from 25 ° C) 35 PPM Typical environmental specification per degree Celsius Operating temperature 0 ° C to+60 ° C (+32 ° to+140 ° F) Storage temperature - 40 ° to+100 ° C (- 40 ° to+212 ° F) Humidity 5% to 95% (non condensing) Vibration 5-10 Hz 0.2 "(5.08mm) Displacement, 10-200 Hz under 1G Refer to GFK-0867B for product standards and general specifications. * In case of serious RF interference (IEC 801-3, 10 V/m) The accuracy may decrease to+/- 0.25% of the full scale reading
