5SHX2645L0006工控模块卡件
串行端口
本数据表适用于CPU 350模块，（32 KB用户内存，4K I/O，8个机架），无内置串行端口，.2 提供此90-30模块的接线图和安装指南。有关更多信息，请致电1-866-599-6507联系Cimtec技术支持sales@cimtecautomation.com5-34系列90-30 PLC安装和硬件手册–2002年8月GFK-0356Q 5 CPU350目录号CPU类型单槽CPU模块每个系统8的总基板（CPU基板+7扩展和/或远程）电源所需负载670毫安，+5 VDC电源处理器速度25兆赫处理器类型80386EX工作温度0至60摄氏度（32至140华氏度）环境典型扫描速率0.22毫秒每1K逻辑（布尔触点）用户程序存储器（最大）32K字节（不可配置）
系统寄存器
离散输入点-%I 2048离散输出点-%Q 2048离散全局存储器-%G 1280位内部线圈-%M 4096位输出（临时）线圈-%T 256位系统状态参考-%S 128位（%S、%SA、%SB、%SC各32位）寄存器存储器-%R 9999字模拟输入-%AI 2048字模拟输出-%AQ 512字系统寄存器（仅供参考表查看；不能在用户逻辑程序中引用）28字（%SR）定时器/计数器>2000移位寄存器是内置串行端口1（使用PLC电源上的连接器）。支持SNP/SNP-X从协议。需要CMM模块以支持SNP/SNP-X主协议、CCM或RTU从协议；用于RTU主支持的PCM模块。通信局域网-支持多站。还支持以太网、FIP、Profibus、GBC、GCM、GCM+选项模块。Override Yes Battery Backed Clock Yes Interrupts支持周期性子程序功能类型内存存储RAM和闪存PCM/CCM兼容性Yes浮点数学支持Yes。基于9.0及更高版本固件的固件。CPU 350端口开/关PS
Serial port
This data sheet is applicable to CPU 350 module (32 KB user memory, 4K I/O, 8 racks) without built-in serial port 2 Provide the wiring diagram and installation guide of the 90-30 module. For more information, contact Cimtec Technical Support at 1-866-599-6507 sales@cimtecautomation.com5-34 Series 90-30 PLC Installation and Hardware Manual – August 2002 GFK-0356Q 5 CPU350 Catalog Number CPU Type Single Slot CPU Module The total substrate (CPU substrate+7 expansion and/or remote) power load required for each system 8 is 670 mA, +5 VDC Power Processor Speed 25 MHz Processor Type 80386EX Operating Temperature 0 to 60 ° C (32 to 140 ° F) Environment Typical Scan Rate 0.22 ms per 1K Logic (Boolean Contact) User Program Memory (maximum) 32K bytes (not configurable)
System register
Discrete input point -% I 2048 discrete output point -% Q 2048 discrete global memory -% G 1280 bit internal coil -% M 4096 bit output (temporary) coil -% T 256 bit system status reference -% S 128 bit (32 bits each for% S,% SA,% SB,% SC) register memory -% R 9999 word analog input -% AI 2048 word analog output -% AQ 512 word system register (for reference table only; cannot be referenced in user logic program) 28 words (% SR) The timer/counter>2000 shift register is the built-in serial port 1 (using the connector on the PLC power supply). Support SNP/SNP-X slave protocol. CMM module is required to support SNP/SNP-X master protocol, CCM or RTU slave protocol; PCM module for RTU main support. Communication LAN - supports multiple stations. It also supports Ethernet, FIP, Profibus, GBC, GCM, and GCM+option modules. Override Yes Battery Backed Clock Yes Interrupts supports periodic subprogram function types Memory storage RAM and flash memory PCM/CCM compatibility Yes Floating point math supports Yes. Firmware based on firmware version 9.0 and later. CPU 350 port on/off PS
