3HB012961R0001工控DCS系统备件
配置模块
在最大尺寸PLC存储之后使用HHP配置模块时发生致命故障IC693 PLC CPU可能在尝试使用手持编程器（HHP）在最大尺寸存储之后配置模块时产生致命故障。用清除M/T加电后固件更新失败和写入闪存固件更新可能会在按下手持编程器上的清除M/T并写入闪存加电后失败。在PLC上循环通电将使升级得以继续。使用这两个模块的文档说明可在以下手册的最新版本中找到：硬件说明、，安装说明：IC693安装和硬件手册一般配置说明：IC63PLC编程软件用户手册系统操作：IC693PLC系统手册系统操作和说明集：IC693APLC参考手册6重要产品信息GFK-1512M IC693CPU350数据CPU类型单槽CPU模块每个系统的总底板8（CPU基板+7扩展和/或远程）电源所需负载670毫安，+5 VDC电源处理器速度25兆赫处理器类型80386EX典型扫描速率。
用户程序存储器
每1K逻辑22毫秒（布尔触点）用户程序存储器（最大）32K字节（不可配置）离散输入点-%I 2048离散输出点-%Q 2048离散全局存储器-%G 1280位内部线圈-%M 4096位输出（临时）线圈-%T 256位系统状态参考-%S 128位（%S、%SA、%SB、%SC各32位）寄存器内存-%R 9999字模拟输入-%AI 2048字模拟输出-%AQ 512字系统寄存器（仅用于参考表查看；不能在用户逻辑程序中引用）28字（%SR）定时器/计数器>2000移位寄存器是内置串行端口1（使用PLC电源上的连接器）。支持SNP、SNP-X从协议。需要CMM模块以支持SNP/SNP-X主、CCM或RTU（从）协议。RTU主支持需要PCM模块。通信LAN–支持多站。还支持以太网、FIP、Profibus、GBC、GCM和GCM+选项模块。覆盖是电池供电时钟是中断支持周期性子程序功能。内存存储RAM和闪存PCM/CCM兼容性类型是浮点数学支持是，固件版本9.0及更高版本中基于固件。
Configuration module
Fatal failure when using HHP configuration module after maximum size PLC storage IC693 PLC CPU may cause a fatal failure when trying to configure module after maximum size storage using handheld programmer (HHP). Firmware update failure after powering up by clearing M/T and writing flash firmware update may fail after powering up by pressing Clear M/T and writing flash on the hand-held programmer. Cycling power on the PLC will allow the upgrade to continue. The documentation for using these two modules can be found in the latest versions of the following manuals: Hardware Description, Installation Instructions: IC693 Installation and Hardware Manual General Configuration Instructions: IC63PLC Programming Software User Manual System Operation: IC693PLC System Manual System Operation and Description Set: IC693APLC Reference Manual 6 Important Product Information GFK-1512M IC693CPU350 Data CPU Type Single Slot CPU Module The total backplane of each system 8 (CPU substrate+7 expansion and/or remote) The load required for the power supply is 670mA, +5 VDC Power Processor Speed 25 MHz Processor Type 80,386EX Typical Scan Rate.
User program memory
22 msec per 1K logic (boolean contact) user program memory (maximum) 32K bytes (unconfigured) discrete input point -% I 2048 discrete output point -% Q 2048 discrete global memory -% G 1280 bit internal coil -% M 4096 bit output (temporary) coil -% T 256 bit system status reference -% S 128 bit (32 bits each for% S,% SA,% SB,% SC) Register memory -% R 9999 word analog input -% AI 2048 word analog output -% AQ 512 word system register (for reference table viewing only; cannot be referenced in user logic programs) 28 word (% SR) timer/counter>2000 shift register is the built-in serial port 1 (using the connector on the PLC power supply). Support SNP and SNP-X slave protocols. CMM module is required to support SNP/SNP-X master, CCM or RTU (slave) protocol. The PCM module is required for RTU main support. Communication LAN – supports multiple stations. Ethernet, FIP, Profibus, GBC, GCM and GCM+Option Modules are also supported. Overrides are battery powered clocks that interrupt support periodic subroutine functions. The compatibility type of memory storage RAM and flash memory PCM/CCM is floating-point math support. Firmware versions 9.0 and later are based on firmware.
