5SHX1445H0001模块卡件
此版本解决的问题
言本文件包含任何其他出版物中没有的信息；因此，我们建议您保存它以备将来参考。本文档讨论了固件版本10.60，该版本修复了“此版本解决的问题”（第4页）中列出的问题。此版本未添加任何新功能。硬件标识下表显示了这些CPU当前版本中使用的电路板的修订级别。CPU目录号电路板ID电路板版本IC693CPU350-CG CX3A1或CX3B1 44A739579-G01R04或更新版本44A749514-G01R00或更新版本IC693CPU360-CH CX3A1 CX3B1 44A 739579/G01R04或者更新版本44A 749514G01R00或者更新版本IC69 3CPU363-BF CX3A1 44A 7395 79-G01R105或更新版本固件升级套件如果您希望将现有CPU350或CPU360升级到固件版本10.00，您可以购买下表中确定的适用套件。所有以前的版本都可以升级。固件升级套件目录号CPU目录号固件升级套件产品目录号IC693CPU350-（所有版本）44A747145-G06 IC693CPU360-（所有版）44A7148-G07 IC693CPU363-BF 44A747766-G05 2重要产品信息GFK-1512M固件标识CPU目录号主板固件版本子板固件版本IC693CCU350-CG主版本：R10.60（38A1）引导：R9.00（33A1）N/A IC693CPU360-CH主：R10.60（38A1）引导：R9.00。固件升级是在软盘上提供的，必须从个人计算机上串行下载。需要一台IBM AT个人计算机或更好的PC，至少640K RAM，一个3.5英寸软盘驱动器，MS-DOS 3.3或更高版本（或Windows 95或更高），一个硬盘驱动器和一个RS-232串行端口。此外，还需要串行电缆和RS232/RS-485转换器。
Fanuc提供以下串行电缆/转换器套件：具有串行电缆功能兼容性的IC690ACC901迷你转换器（RS-232/RS-485）套件•需要CIMPLICTY机器版PLC逻辑开发人员2.11或更高版本，或VersaPro 1.1或更高版，才能利用10.00版固件中引入的功能。•C编程需要PLC Logic Developer、VersaPro 2.00或更高版本或控制软件2.00或更低版本。•C工具包的4.00版或更高版本必须用于C编程。•必须使用2.00或更高版本的控制软件来利用顺序功能图（SFC）子程序。•必须使用Logicmaster软件版本9.02或更高版本才能利用固件版本9.00中引入的功能。重要产品信息3 GFK-1512M操作说明升级固件时清除的用户信息用户信息，包括程序、配置、CPU ID（用于SNP通信）和RAM内存中的状态表，如果闪存中的CPU固件发生更改，将自动清除。如果升级固件，则需要恢复这些。建议的步骤是首先将用户信息从RAM内存备份到闪存。然后将新固件写入闪存（固件存储在闪存中与用于存储用户信息（如程序、配置等）的位置不同的位置）。最后，将您的用户信息从闪存写回RAM内存。或者，可以使用PLC编程软件从基于计算机的备份程序文件夹中恢复用户信息（程序、配置等）。如果需要，必须使用编程软件或手持编程器（HHP）单独设置SNP ID。选项模块修订要求•以太网接口模块兼容性。与这些CPU一起使用的所有IC693 Ethernet Interface（IC693CMM321）模块应更新至IC693CMM 321固件版本1.10或更高版本。这也是MS-DOS编程软件的TCP/IP以太网版本的要求。在大型程序块（大于14 KB）的运行模式存储（Alt+S热键组合）期间，以太网模块可能会超时，导致通信失败。将通信窗口更改为“运行”至“完成”模式，或将程序存储为“停止”模式，将使存储成功进行。•FBC兼容性。这些CPU需要FBC版本3或更高版本。
Problems solved by this version
This document contains information not found in any other publication; Therefore, we recommend that you save it for future reference. This document discusses firmware version 10.60, which fixes the problems listed in "Problems solved by this version" (page 4). No new features have been added to this version. The following table shows the revision level of the circuit boards used in the current version of these CPUs. CPU Catalog Number Circuit board ID Circuit board version IC693CPU350-CG CX3A1 or CX3B1 44A739579-G01R04 or newer version 44A749514-G01R00 or newer version IC693CPU360-CH CX3A1 CX3B1 44A 739579/G01R04 or newer version 44A 749514G01R00 or newer version IC69 3CPU363-BF CX3A1 44A 7395 79-G01R105 or newer firmware upgrade kit If you want to upgrade an existing CPU350 or CPU360 to firmware version 10.00, You can purchase the applicable kits identified in the table below. All previous versions can be upgraded. Firmware Upgrade Kit Catalog No. CPU Catalog No. Firmware Upgrade Kit Catalog No. IC693CPU350 - (all versions) 44A747145-G06 IC693CPU360 - (all versions) 44A7148-G07 IC693CPU363-BF 44A747766-G05 2 Important Product Information GFK-1512M Firmware Identification CPU Catalog No. Mainboard Firmware Version Subboard Firmware Version IC693CCU350-CG Main Version: R10.60 (38A1) Boot: R9.00 (33A1) N/A IC693CPU360-CH Main: R10.60 (38A1) Boot: R9.00. Firmware upgrades are provided on floppy disks and must be downloaded serially from a personal computer. An IBM AT personal computer or better PC, at least 640K RAM, a 3.5 inch floppy disk drive, MS-DOS 3.3 or higher (or Windows 95 or higher), a hard disk drive and an RS-232 serial port are required. In addition, a serial cable and an RS232/RS-485 converter are required.
Fanuc offers the following serial cable/converter kits: IC690ACC901 Mini Converter (RS-232/RS-485) kit with serial cable functional compatibility • CIMPLICTY Machine PLC Logic Developer 2.11 or later, or VersaPro 1.1 or later, is required to take advantage of the features introduced in firmware version 10.00. • C programming requires PLC Logic Developer, VersaPro 2.00 or later, or control software 2.00 or earlier. • Version 4.00 or higher of the C toolkit must be used for C programming. • Control software version 2.00 or higher must be used to make use of sequential function diagram (SFC) subprograms. • Logicmaster software version 9.02 or later must be used to take advantage of features introduced in firmware version 9.00. Important Product Information 3 GFK-1512M Operating Instructions User information cleared when upgrading firmware, including program, configuration, CPU ID (for SNP communication) and status table in RAM memory. If CPU firmware in flash memory changes, it will be automatically cleared. If you upgrade the firmware, you need to restore these. The recommended procedure is to first back up user information from RAM memory to flash memory. The new firmware is then written to flash memory (where the firmware is stored is different from where user information (such as programs, configurations, etc.) is stored). Finally, write your user information back to RAM memory from flash memory. Alternatively, the PLC programming software can be used to recover user information (programs, configurations, etc.) from the computer based backup program folder. If necessary, the SNP ID must be set separately using programming software or a hand-held programmer (HHP). Option Module Revision Requirements • Ethernet Interface Module Compatibility. All IC693 Ethernet Interface (IC693CMM321) modules used with these CPUs should be updated to IC693CMM 321 firmware version 1.10 or later. This is also a requirement for the TCP/IP Ethernet version of MS-DOS programming software. During the operation mode storage (Alt+S hotkey combination) of large program blocks (larger than 14 KB), the Ethernet module may timeout, causing communication failure. Changing the communication window to "Run" to "Finish" mode or storing the program to "Stop" mode will make the storage succeed. • FBC compatibility. These CPUs require FBC version 3 or later.
