3HNA023093-001DCS卡件
电源要求查看系统的电源要求
以确保机箱支持模块的安装。注：模块在5VDC时消耗850 mA，在24VDC时消耗1.75 mA。对于模块化系统，使用CLX 5000模块化安装和操作手册中描述的程序计算系统电源的总负载，出版物1747-6.2 3.5程序从机的设置分为两部分：•设置从机模块•使从机运行3.5.1设置从机模式以下步骤描述了SST-PB3-CLX-RL设置程序：警告如果在机箱通电时安装模块，确保环境中没有爆炸性或危险的粉尘或气体。如果可能存在气体，请清除有害的灰尘或气体，并在安装模块之前关闭机箱电源。如果不遵守此警告，可能导致严重的人身伤害或设备损坏。1.将从属模块插入1756 CLX机箱。2.使用适当的电缆和终端将从设备连接到PROFIBUS网络。有关更多详细信息，请参阅第4.2节PROFIBUS接线。3.在安全的情况下为CLX通电。4.将CLX PLC置于编程模式。有关详细信息，请参阅编程软件手册。用户参考指南 18 Quick Start©2014 Molex股份有限公司工业产品业务部，综合产品部文件版本：1.0，文件#：715-0109，模板版本：1.1，模板ţ：QMS-06-045本文件或其中包含的任何信息的使用、复制或披露受本文件第二页的限制。3.5.2使从模块运行以下步骤描述了如何设置：1.启动RSLogix5000或Studio 5000软件。2.选择I/O Configuration文件夹，选择New Module，选择Molex Incorporated in Module Type Vendor Filters，选择SST-PB3-CLX-RLL，然后选择Create按钮。3.在常规选项卡中，填写名称字段，选择机箱中的模块插槽编号。在模块定义区域中，选择更改按钮 User Reference Guide Quick Start 19©2014 Molex股份有限公司工业产品业务部门，
集成产品部门文档版本：
1.0，文档#：715-0109，模板版本：1.1，模板35；：QMS-06-045 Use，复制或披露本文件或其中包含的任何信息均受本文件第ii页的限制。4.在模块定义窗口中，在模式菜单中选择从属，然后选择确定。用户参考指南 20 Quick Start©2014 Molex股份有限公司工业产品业务部门，集成产品部门文档版本：1.0，文档#：715-0109，模板版本：1.1，模板35；：QMS-06-045使用，复制或披露本文件或其中包含的任何信息均受本文件第ii页的限制。5.在模块配置选项卡中，选择从站模式下拉列表，选择自动运行，填写从站数据传输大小、Profibus从站编号（地址）、Profibus波特率，选择确定。有关需要设置的参数的更多详细信息，请参见第6.5.2节，如下图红色所示。用户参考指南安装 Slave 21©2014 Molex股份有限公司工业产品业务部门，综合产品部文件版本：1.0，文件#：715-0109，模板版本：1.1，模板35；：QMS-06-045使用，复制或披露本文件或其中包含的任何信息均受本文件第ii页的限制。4安装从机章节：•安装从机模块•PROFIBUS布线•PROFIBUS LED和显示状态•LED和显示组合用户参考指南 22安装从机©2014 Molex股份有限公司工业产品业务部，集成产品部文件版本：1.0，文件#：715-0109，模板版本：1.1，模板编号：QMS-06-045使用、复制或披露本文件或其中包含的任何信息均受本文件第ii页的限制。4.1安装从模块4.1.1安装程序以下程序描述了如何安装从模块：警告如果在机箱通电时安装模块，请确保环境中没有爆炸性或危险的灰尘或气体。如果可能存在气体，请清除有害的灰尘或气体，并在安装模块之前关闭机箱电源。如果不遵守此警告，可能导致严重的人身伤害或设备损坏。1.您可以，但不一定需要断开电源，因为从设备支持在电源下插入。阅读并遵循上述警告。2.使用机箱卡导轨，对齐全尺寸电路板。
Power Requirements View the power requirements of the system
To ensure that the chassis supports module installation. Note: The module consumes 850 mA at 5VDC and 1.75 mA at 24VDC. For a modular system, use the program described in the CLX 5000 Modular Installation and Operation Manual to calculate the total load of the system power supply. The setup of the program slave in Publication 1747-6.2 3.5 is divided into two parts: • Set the slave module • Make the slave run 3.5.1 Set the slave mode The following steps describe the SST-PB3-CLX-RL setup procedure: Warning If you install the module when the chassis is powered on, ensure that there is no explosive or dangerous dust or gas in the environment. If gas may be present, remove harmful dust or gas and turn off the chassis before installing the module. Failure to observe this warning may result in serious personal injury or equipment damage. 1. Insert the slave module into the 1756 CLX chassis. 2. Connect the slave device to the PROFIBUS network using appropriate cables and terminals. Refer to Section 4.2 PROFIBUS Wiring for more details. 3. Power on CLX when it is safe to do so. 4. Put the CLX PLC in programming mode. Refer to the programming software manual for more information. User Reference Guide 18 Quick Start © 2014 Molex Co., Ltd. Industrial Products Business Department, Integrated Products Department Document version: 1.0, Document #: 715-0109, Template version: 1.1, Template ţ： QMS-06-045 The use, reproduction or disclosure of this document or any information contained therein is restricted by the second page of this document. 3.5.2 The following steps for running the slave module describe how to set: 1. Start the RSLogix5000 or Studio 5000 software. 2. Select the I/O Configuration folder, New Module, Molex Incorporated in Module Type Vendor Filters, SST-PB3-CLX-RLL, and then Create. 3. In the General tab, fill in the Name field and select the module slot number in the chassis. In the module definition area, select the change button User Reference Guide Quick Start 19 © Industrial Products Business Department of Molex Co., Ltd. in 2014,
Integration Product Department Document Version:
1.0, Document #: 715-0109, Template Version: 1.1, Template 35;: QMS-06-045 Use, Reproduction or disclosure of this document or any information contained therein are subject to the restrictions of page ii of this document. 4. In the module definition window, select Slave in the mode menu, and then select OK. User Reference Guide 20 Quick Start © 2014 Molex Co., Ltd. Industrial Products Business Department, Integrated Products Department Document Version: 1.0, Document #: 715-0109, Template Version: 1.1, Template 35;: QMS-06-045 The use, reproduction or disclosure of this document or any information contained therein is subject to the restrictions of page ii of this document. 5. In the module configuration tab, select the slave mode drop-down list, select automatic operation, fill in the slave data transmission size, Profibus slave number (address), and Profibus baud rate, and select OK. For more details on the parameters to be set, see Section 6.5.2, as shown in red below. User Reference Guide Installing Slave 21 © 2014 Molex Co., Ltd. Industrial Products Business Department, Integrated Products Department Document Version: 1.0, Document #: 715-0109, Template Version: 1.1, Template 35;: QMS-06-045 The use, reproduction or disclosure of this document or any information contained therein is subject to the restrictions of page ii of this document. 4 Chapter of Installing Slave: • Installing Slave Module • PROFIBUS Wiring • PROFIBUS LED and Display Status • LED and Display Combination User Reference Guide 22 Installing Slave © 2014 Molex Co., Ltd. Industrial Products Business Department, Integrated Products Department Document version: 1.0, Document #: 715-0109, Template version: 1.1, Template number: QMS-06-045 The use, copying or disclosure of this document or any information contained in it are subject to the restrictions of page ii of this document. 4.1 Installing Slave Module 4.1.1 Installation Procedure The following procedure describes how to install a slave module: Warning If you install the module when the chassis is powered on, make sure that there is no explosive or dangerous dust or gas in the environment. If gas may be present, remove harmful dust or gas and turn off the chassis before installing the module. Failure to observe this warning may result in serious personal injury or equipment damage. 1. You can, but it is not necessary to disconnect the power supply, because the slave device supports inserting under the power supply. Read and follow the above warnings. 2. Use the chassis card guide to align the full-size circuit board.
