工控DCS系统备件3HAC031683-001
选择屏幕
选择项目输入转到子屏幕F1常规帮助F10保存并退出ESC退出警告：在下面的部分中设置错误的值可能会导致系统故障。¾Intel Montara NorthBridge配置¾Hance Rapids SouthBridge设置¾CPCI（HINT HB6）网桥配置¾Lan（8254EB）端口路由选项Artisan Technology Group-Quality Instrumentation。保证|SOURCE|articatg 87退出菜单B退出菜单从ezPORT设置屏幕选择退出选项卡，进入退出BIOS设置屏幕。您可以使用按键突出显示退出BIOS设置选项。退出BIOS设置屏幕如下所示。002.53（C）版权所有1985-2002，American Megatrends，股份有限公司。如果之前对BIOS和系统故障进行了更改，请重新启动系统并访问此屏幕。选择“加载故障保护默认值”并继续重新启动。BIOS设置实用程序主高级PCIPnP引导安全芯片组退出退出选项保存更改后退出系统设置。F10键可用于此操作选择屏幕↑↓ 选择项目输入转到子屏幕F1常规帮助F10保存并退出ESC退出保存更改并退出放弃更改并退出丢弃更改加载最佳默认值加载故障保护默认值Artisan Technology Group-Quality Instrumentation。保证|来源|工匠88 B-7807/RC产品手册本页特意留空。Artisan Technology Group-质量仪器。 允许从网络引导SBC。
设置屏幕的过程
C Artisan Technology Group-质量仪器。保证|SOURCE|articatg 90 C-7807/RC产品手册引导菜单有两种方法可以启用Argon BIOS选项。第一种方法是第一引导菜单。第二个是BIOS设置实用程序中的引导菜单。第一引导菜单在引导周期的最开始按F11，将访问第一引导菜单。在此屏幕中选择“托管PC引导代理（MBA）”从LAN引导仅适用于当前引导，在下次重新引导时，-7807/RC将恢复到引导菜单中的设置。使用箭头键，突出显示Managed PC Boot Agent（MBA），然后按ENTER键继续系统引导。引导菜单启用Argon BIOS选项的第二种方法是在系统引导期间按DEL键。这将访问BIOS设置实用程序。前进到Boot（引导）菜单，然后进入Boot Device Priority（引导设备优先级）子菜单。使用箭头键突出显示Managed PC Boot Agent（MBA）选项。重复输入，直到所需的MBA名列榜首。进入退出菜单，选择“退出保存更改”，然后按ENTER键。当系统提示确认时，按“”。然后，计算机将重新启动系统引导。
Selection screen
Select Item Input Go to the sub screen F1 General Help F10 Save and Exit ESC Exit Warning: Setting an incorrect value in the following section may cause system failure. ¾ Intel Montara NorthBridge Configuration ¾ Hance Rapids SouthBridge Settings ¾ CPCI (HINT HB6) bridge configuration ¾ Lan (8254EB) port routing option Artisan Technology Group Quality Instrumentation. Ensure that | SOURCE | articatg 87 Exit Menu B Exit Menu Select the Exit tab from the ezPORT setup screen to enter the Exit BIOS setup screen. You can use the key to highlight the Exit BIOS Setup option. Exit the BIOS setup screen as shown below. 002.53 (C) Copyright 1985-2002, American Megatrends, Inc. If changes were made to the BIOS and system faults, restart the system and access this screen. Select Load Failsafe Defaults and continue restarting. BIOS Setup Utility Main Advanced PCIPnP Boot Security Chipset Exit Exit option Exit system setup after saving changes. F10 key can be used for this operation Selection screen ↑↓ Select item input Go to sub screen F1 General Help F10 Save and exit ESC Exit Save Changes and Exit Discard Changes Load Best Default Value Load Failure Protection Default Value Artisan Technology Group Quality Instrumentation. Warranty | Source | Artisan 88 B-7807/RC Product Manual This page is intentionally left blank. Artisan Technology Group - quality instrument. Allows SBC to boot from the network.
Procedure for setting the screen
C Artisan Technology Group - quality instrument. Ensure that the Argon BIOS option can be enabled in the | SOURCE | articatg 90 C-7807/RC product manual boot menu in two ways. The first method is the first boot menu. The second is the boot menu in the BIOS setup utility. Press F11 at the beginning of the boot cycle to access the first boot menu. In this screen, select "Managed PC Boot Agent (MBA)" to boot from the LAN only for the current boot. On the next reboot, - 7807/RC will revert to the settings in the boot menu. Use the arrow keys to highlight the Managed PC Boot Agent (MBA), and then press ENTER to continue the system boot. The second way to enable the Argon BIOS option in the boot menu is to press the DEL key during system boot. This accesses the BIOS setup utility. Advance to the Boot menu and enter the Boot Device Priority submenu. Use the arrow keys to highlight the Managed PC Boot Agent (MBA) option. Repeat the entry until the required MBA is at the top of the list. Enter the Exit menu, select Exit Save Changes, and then press ENTER. When prompted to confirm, press "". The computer will then restart the system boot.
