3HAC025562-00106工控备件
以太网必须通过任一前面板（RJ45）连接器连接
才能远程启动。此功能允许用户创建系统，而无需担心磁盘驱动器的可靠性或添加CompactFlash驱动器的额外成本。引导BIOS功能：Netware（802.1、802.3或EthII）、TCP/IP（DHCP或BootP）、，RPL和PXE引导支持无与伦比的引导扇区病毒保护详细的引导配置屏幕全面诊断可选禁用本地引导双引导选项允许用户选择网络或本地引导Artisan Technology Group-Quality Instrumentation。保证|来源| artisantg 60 3-7807/RC产品手册本页特意留空。Artisan Technology Group-Quality Instrumentation.Guarantee | SOURCE | artisatg 61维护如果GE Fanuc嵌入式系统产品出现故障，请验证以下内容：1.产品上的软件2.系统配置3.电气连接4.跳线或配置选项5.电路板完全插入其正确的连接器位置6。连接器引脚清洁且无污染7。从机箱中插入或卸下电路板时，没有任何组件或相邻电路板受到干扰8。电缆和I/O连接的质量如果必须退货，请联系GE Fanuc Embedded Systems获取退货授权（RMA）编号。退货前必须获得此RMA编号。，或发送电子邮件优质仪器。
说明书
合规信息本章提供了有关-7807/RC合规性的适用信息对-7807/RC进行了评估，它们符合以下标准国际合规性这些产品也符合以下国际标准。欧盟EN55024（1998 w A1:01&A2:03）CISPR22、EN55022（A类）CISPR11、EN55011（A类，第1组）美国FCC第15部分B子部分第109节，A类CISPR 22（1997），A级ANSI C63.4（2003）方法澳大利亚/新西兰AS/NZS CISPR 22（2002）A级使用：EN55022（1998）A级日本VCCI（2005年4月设备符合FCC规则第15部分。操作必须符合以下两个条件：（1）本设备可能不会造成有害干扰，以及（2）本设备必须接受接收到的任何干扰，包括可能导致不期望操作的干扰。FCC A类注：根据FCC规则第15部分，该设备已测试并符合A类数字设备的限制。当设备在商业环境中运行时，这些限制旨在提供合理的保护，防止有害干扰。本设备产生、使用和辐射射频能量，如果未按照说明手册安装和使用，可能会对无线电通信造成有害干扰。在住宅区操作该设备可能会造成有害干扰，在这种情况下，用户需要自费纠正干扰。注意：未经负责合规的一方明确批准的更改或修改可能会使用户无权操作设备。
Ethernet must be connected through any front panel (RJ45) connector
To start remotely. This feature allows users to create systems without worrying about the reliability of disk drives or the additional cost of adding CompactFlash drives. Boot BIOS function: Netware (802.1, 802.3 or EthII), TCP/IP (DHCP or BootP),, RPL and PXE boot support incomparable boot sector virus protection Detailed boot configuration screen Comprehensive diagnosis Optional disable local boot dual boot option allows users to choose network or local boot Artisan Technology Group Quality Instrumentation. Warranty | Source | Artisantg 60 3-7807/RC Product Manual This page is intentionally left blank. Artisan Technology Group-Quality Instrumentation. Guarantee | SOURCE | Artisatg 61 Maintenance If the GE Fanuc embedded system product fails, please verify the following: 1. Software on the product 2. System configuration 3. Electrical connection 4. Jumper or configuration option 5. The circuit board is fully inserted into its correct connector location6. The connector pins are clean and free of contamination 7. When a circuit board is inserted or removed from the chassis, no components or adjacent circuit boards are interfered with 8. If the quality of cables and I/O connections must be returned, please contact GE Fanuc Embedded Systems for a Return Authorization (RMA) number. This RMA number must be obtained before return., Or send email to quality instrument.
Instructions
Compliance Information This chapter provides applicable information about the compliance of - 7807/RC. The - 7807/RC has been evaluated. They comply with the following standards. International compliance. These products also comply with the following international standards. EU EN55,024 (1998 w A1:01&A2:03) CISPR22, EN55,022 (Class A) CISPR11, EN55,011 (Class A, Group 1) US FCC Part 15, Subpart B, Section 109, Class A CISPR 22 (1997), Class A ANSI C63.4 (2003) method Australia/New Zealand AS/NZS CISPR 22 (2002) Class A use: EN55022 (1998) Class A Japanese VCCI (in April 2005, the equipment complies with Part 15 of the FCC Rules. The operation must meet the following two conditions: (1) the equipment may not cause harmful interference, and (2) the equipment must accept any interference received, including interference that may cause unexpected operation. FCC Class A Note: According to Part 15 of the FCC Rules, this equipment has been tested and meets the limits of Class A digital equipment. These limits are intended to provide reasonable protection against harmful interference when the equipment is operating in a commercial environment. This equipment generates, uses and radiates radio frequency energy. If it is not installed and used according to the instruction manual, it may cause harmful interference to radio communication. Operating the equipment in residential areas may cause harmful interference, in which case the user needs to correct the interference at his own expense. Note: Changes or modifications not expressly approved by the party responsible for compliance may result in users having no right to operate the equipment.
