3BDH000320R0101模块卡件
状态指示灯
（从左到右）Sysfail VME故障-VME Sysfail状态期间亮起（红色指示灯）。PWR Power（PWR电源）-指示板何时通电（绿色LED）。IDE活动指示器-当IDE活动发生时闪烁（黄色LED）。引导完成引导-表示BIOS引导正在进行。LED熄灭时，CPU已完成POST并准备就绪（红色LED）。RST Switch Reset（重新设置开关）-允许从前面板重置系统。10/100以太网LED链路指示以太网处于活动状态（绿色LED）。活动指示是10BaseT（黄色LED）还是100BaseTX绿色LED）模式处于活动状态。前千兆以太网LED链路指示以太网处于活动状态（黄色LED）。活动指示是10BaseT（LED熄灭）、100BaseTX（黄色LED）还是1000BaseT（绿色LED）以太网模式处于活动状态。后千兆以太网LED链路指示以太网处于活动状态（绿色LED）。活动指示是10BaseT（LED熄灭）、100BaseTX（黄色LED）还是1000BaseT（绿色LED）以太网模式处于活动状态。图1-5前面板布局P M C U S B G 2 G 1 RST S VMIVME 7807 1 0/1 0 C O M 1 PMC USBs 10/100千兆以太网千兆以太网LED COM1鼠标/键盘SVGA链接活动链接活动活动34 1 产品手册本页特意留空。 是基于奔腾M处理器的单板计算机，与现代工业标准桌面系统兼容。因此，保留了工业标准内存和I/O映射以及标准中断架构。
集成外围设备
（如串行端口、USB端口、IDE驱动器、软盘驱动器、视频控制器和以太网控制器）都与配备类似设备的桌面系统相同，以确保与现代操作系统的兼容性。以下章节描述了的标准功能。2 36 2 产品手册CPU VMIVME-8807/VME-7807RC CPU出厂时使用奔腾M处理器。CPU速度和内存/CompactFlash大小由用户指定，作为订购信息的一部分。要更改内存大小或CompactFlash大小，请联系客户服务部以获得退货授权（RMA）。RMA可在rma@gefanuc.com.GE Fanuc嵌入式系统客户服务热线：1-800-GEFANUC（或1-800-433-2682）、1-780-401-7700或发送电子邮件至support.embeddedsystems@gefanuc.com.物理内存提供DDR同步DRAM（SDRAM）作为板载系统内存。内存可以以字节、字或长字的形式访问。接受一个200引脚DDR SDRAM SODIMM以及512MB板载内存中的可选焊料，最大容量为1.5GB。VME可通过PCI到PCI桥访问板载DRAM，并可由本地处理器寻址。注：内存容量可能会因零件可用性而变化。37 PCI设备中断映射2 PCI设备中断图基于PCI总线的外部设备包括Universe IID桥、PMC站点、以太网控制器、FPGA和GE Fanuc嵌入式系统连接器。默认BIOS将这些外部设备映射到6300ESB I/O控制器集线器的PCI中断请求（PIRQx）行。此映射在表2-1中定义。*Intel 82546EB的设备ID为1010H。Intel 82546GB的设备ID为1079H。
Status indicator
(From left to right) Sysmail VME fault lights up during the VME Sysmail state (red indicator). PWR Power - Indicates when the board is powered on (green LED). IDE activity indicator - blinks when IDE activity occurs (yellow LED). Boot Complete Boot - Indicates that BIOS boot is in progress. When the LED is off, the CPU is ready for POST (red LED). RST Switch Reset - Allows the system to be reset from the front panel. The 10/100 Ethernet LED link indicates that the Ethernet is active (green LED). Active indicates whether the 10BaseT (yellow LED) or 100BaseTX green LED) mode is active. The front Gigabit Ethernet LED link indicates that the Ethernet is active (yellow LED). Activity indicates whether 10BaseT (LED off), 100BaseTX (yellow LED), or 1000BaseT (green LED) Ethernet mode is active. The rear Gigabit Ethernet LED link indicates that the Ethernet is active (green LED). Activity indicates whether 10BaseT (LED off), 100BaseTX (yellow LED), or 1000BaseT (green LED) Ethernet mode is active. Figure 1-5 Front Panel Layout P M C U S B G 2 G 1 RST S VMIVME 7807 1 0/1 0 C O M 1 PMC USBs 10/100 Gigabit Ethernet LED COM1 Mouse/Keyboard SVGA Link Active Link Active 34 1 This page of the product manual is intentionally left blank. It is a single board computer based on Pentium M processor and compatible with modern industrial standard desktop system. Therefore, the industry standard memory and I/O mapping as well as the standard interrupt architecture are retained.
Integrated peripherals
(such as serial port, USB port, IDE drive, floppy disk drive, video controller and Ethernet controller) are the same as desktop systems equipped with similar devices to ensure compatibility with modern operating systems. The following sections describe the standard features of. 2 36 2 Product Manual CPU VMIVME-8807/VME-7807RC CPU is delivered with Pentium M processor. The CPU speed and memory/CompactFlash size are specified by the user as part of the ordering information. To change the memory size or CompactFlash size, contact Customer Service for a Return Authorization (RMA). RMA can rma@gefanuc.com.GE Fanuc Embedded System Customer Service Hotline: 1-800-GEFANUC (or 1-800-433-2682), 1-780-401-7700 or email to support.embeddedsystems@gefanuc.com. The physical memory provides DDR synchronous DRAM (SDRAM) as the on-board system memory. Memory can be accessed in bytes, words, or long words. Accepts a 200 pin DDR SDRAM SODIMM and optional solder in 512MB on-board memory, with a maximum capacity of 1.5GB. VME can access on-board DRAM through PCI to PCI bridge and can be addressed by local processor. Note: Memory capacity may vary depending on part availability. 37 PCI device interrupt map 2 PCI device interrupt map PCI bus based external devices include universe IID bridge, PMC site, Ethernet controller, FPGA and GE Fanuc embedded system connector. The default BIOS maps these external devices to the PCI Interrupt Request (PIRQx) line of the 6300ESB I/O controller hub. This mapping is defined in Table 2-1* The device ID of Intel 82546EB is 1010H. The device ID of Intel 82546GB is 1079H.
