500SCM01 1MRB150004R0001 连接器用于模拟量模块全新 ABB
流量计
作为安全功能系统的一部分图1：安全功能（例如最小/最大流量监测），流量计作为子系统a ProcessMaster或HygiicMaster b笔记本电脑，带有配置工具，如SMART VISION c FSK调制解调器D手持终端e自动化系统、逻辑单元、PLC、报警信号单元、，流量计变送器产生与流量成比例的模拟信号（4…20 mA）。模拟信号被馈送至下游逻辑单元，如PLC或报警信号单元，并被监控是否超过规定的最大值或最小值。注意：安全相关信号是流量计变送器的4…20 mA模拟输出信号。所有安全功能仅指该模拟输出（端子31/32）。5.1与功能安全相关的设备特定数据Term Value DeviceType ProcessMaster FEP300、FEP500、HygiicMaster FEH300、，FEH500固件级别从2001年2月1日至2002年3月1日硬件级电子隔间零件号D674A903U01版本05至13零件号D774A904U01版本05-13零件号D574A905U01版本06-13零件编号D674A 906U01版本03-13根据IEC 61508-2路由2S硬件容错架构路由2H根据IEC 61608-2 SIL在使用中验证的评估类型能力SIL2（低需求模式）HFT 0组件B类故障率SIL检测器在DC上关闭10年后的故障率为71.1%82.6%PFDAVG，验证测试间隔为1年，验证测试覆盖率为90%（对FEX311、FEX511、FEX315、FEX325、FEX525有效）2,65E-03、51E-03 PFDAVG6年后的验证测试间隔1年，证明测试覆盖率90%（对FEX321、FEX5121有效）2,09E-031,20E-03λSD 0 FIT 0 FITλSU 943 FIT 943 FITλDD 937 FIT 1070 FIT∧DU 317 FIT 181 FIT NOTICE设备的配置菜单包括一个名为“SIL Detector”的参数。为了确保PFD值符合上表，必须相应地设置探测器。
Flowmeter
As a part of the safety function system Figure 1: safety function (such as minimum/maximum flow monitoring), the flowmeter, as a subsystem a ProcessMaster or HygiicMaster b laptop, is equipped with configuration tools, such as SMART VISION c FSK modem D handheld terminal e automation system, logic unit, PLC, alarm signal unit, and the flowmeter transmitter generates analog signals (4... 20 mA) proportional to the flow. Analog signals are fed to downstream logic units, such as PLC or alarm signal units, and monitored for exceeding specified maximum or minimum values. Note: The safety related signal is the 4... 20 mA analog output signal of the flowmeter transmitter. All safety functions refer only to the analog output (terminal 31/32). 5.1 Term Value DeviceType ProcessMaster FEP300, FEP500, HygiicMaster FEH300, FEH500 firmware level: from February 1, 2001 to March 1, 2002, part number of hardware level electronic compartment: D674A903U01, version 05 to 13, part number: D774A904U01, version 05 - 13, part number: D574A905U01, version 06 - 13, part number: D674A 906U01, version 03 - 13, routing: 2S, hardware fault tolerance architecture routing: 2H, evaluation type capability verified in use according to IEC 61608-2 SIL: SIL2 (low demand mode) Class B failure rate of HFT 0 component The failure rate of SIL detector 10 years after it was shut down on the DC was 71.1% 82.6% PFDAVG, the verification test interval was 1 year, and the verification test coverage was 90% (valid for FEX311, FEX511, FEX315, FEX325, FEX525), the verification test interval was 1 year after 6 years of PFDAVG shutdown, which proved that the test coverage was 90% (valid for FEX321, FEX5121), 2,09E-031,20E-03 λ SD 0 FIT 0 FIT λ SU 943 FIT 943 FIT λ The configuration menu of DD 937 FIT 1070 FIT Λ DU 317 FIT 181 FIT NOTE device includes a parameter named "SIL Detector". To ensure that the PFD value complies with the above table, the detector must be set accordingly.
