SCYC46020 58051217 自动化控制模拟量输入板进口 ABB
电阻器保护
Quality Vision International股份有限公司.规格如有更改，恕不另行通知。保留所有权利。商标是其各自所有者的财产。本产品的出口受美国出口法规的管制。在美国境外交货或再出口可能需要出口许可证。零件号794103-1019-AI810系统800xA硬件选择器数据表AI810模拟输入模块有8个通道。每个通道可以是电压或电流输入。电流互感器能够在不损坏的情况下处理至少30 V直流电对变送器电源的短路。限流由PTC电阻器执行。电流互感器的输入电阻为250欧姆，包括PTC。电压输入能够承受至少30 V直流的过压或欠压。输入电阻为290k欧姆。变送器电源可连接至L1+、L1-和/或L2+、L2-。特点和优点8通道，用于0…20 mA、4…20 mA，0…10 V或2…10 V直流，单端单极输入1组8通道，与地隔离12位分辨率输入分流电阻器，由PTC电阻器保护至30 V。模拟输入短路至ZP或+24 V。输入耐受HART通信。一般信息类型模拟输入信号规格0..20mA、4..20mA、0..10V，2..10V产品编号3BSE008516R1通道数8信号类型单极单端HART无SOE无冗余无高完整性无本质安全无机械S800数据表AI810 | 2019-05-15 |版权所有©2019 ABB 1详细数据分辨率12位输入阻抗290 kΩ（电压输入）230-275 kΩ（电流输入）隔离按组与地隔离低于/高于范围-5%/+15%最大误差0.1%温度漂移电压：典型值。最大70 ppm/°C。100 ppm/°C；电流：类型。50 ppm/°C最大值。
80 ppm/°C输入滤波器
（上升时间0-90%）140ms更新周期时间8ms限流变送器功率可由MTU限流最大现场电缆长度600米（656码）最大输入电压（非破坏性）30 V直流NMRR，50Hz，60Hz>40 dB额定绝缘电压50 V介电测试电压500 V交流。功耗1.5 W电流消耗+5 V模块总线70mA电流消耗+24 V模块总线40mA电流消耗+24 V外部0诊断前LED的F（故障）、R（未）、W（警告）监控内部电源监控状态指示模块错误、模块警告、通道错误环境和认证CE标志是电气安全IEC 61131-2，UL 508危险位置C1 Div 2 cULus、C1 Zone 2 cULus、ATEX Zone 2 Marine认证ABS、BV、DNV-GL、LR、RS、CCS防护等级IP20，符合IEC 60529腐蚀性环境ISA-S71.04 G3气候操作条件0至+55°C（储存-40至+70°C），RH=5至95%无冷凝，IEC/EN 61131-2污染等级2级，IEC 60664-1机械操作条件IEC/EN 61131-2 EMC EN 61000-6-4、EN 61000-6-2过电压类别IEC/EN 60664-11、EN 50178 IEC 61140规定的I类设备；（接地保护）最大环境温度55°C（131°F），用于紧凑型MTU 40°C（104°F）的垂直安装，符合RoHS指令/2011/65/EU（EN 50581:2012）符合WEEE指令/2012/19/EU兼容性与MTU TU810、TU812、TU814、TU818、TU830、TU833、TU835、TU838、TU850键控代码AE尺寸宽45 mm（1.77“）深102 mm（4.01”），111毫米（4.37英寸），包括连接器高度119毫米（4.7英寸），重量0.2千克（0.44磅）2数据表AI810 | 2019-05-15 |版权所有©2019 ABB-相关产品TU810V1 TU812V1 TU824V1 TU830V1 TU833 TU835V1 TU848 TU850数据表AI820 | 2019年05月15日|版权所有
Resistor protection
Quality Vision International Co., Ltd Specifications are subject to change without notice. All rights reserved. Trademarks are the property of their respective owners. The export of this product is subject to the export regulations of the United States. An export license may be required for delivery or re export outside the United States. Part No. 794103-1019-AI810 System 800xA Hardware Selector Data Sheet AI810 Analog Input Module has 8 channels. Each channel can be a voltage or current input. The current transformer shall be able to handle at least 30 V DC short circuit to the transmitter power supply without damage. Current limiting is performed by PTC resistors. The input resistance of current transformer is 250 ohms, including PTC. The voltage input can withstand overvoltage or undervoltage of at least 30 V DC. The input resistance is 290k ohms. The transmitter power supply can be connected to L1+, L1 - and/or L2+, L2 -. Features and advantages 8 channels, used for 0... 20 mA, 4... 20 mA, 0... 10 V or 2... 10 V DC, single ended single pole input 1 group of 8 channels, isolated from the ground with 12 bit resolution input shunt resistor, protected to 30 V by PTC resistor. The analog input is shorted to ZP or+24 V. Input withstands HART communication. General information type Analog input signal specification 0.. 20mA, 4.. 20mA, 0.. 10V, 2.. 10V Product No. 3BSE008516R1 Channel number 8 Signal type Single pole single ended HART No SOE No redundancy No high integrity No intrinsic safety No machinery S800 Data sheet AI810 | 2019-05-15 | All rights reserved © 2019 ABB 1 detailed data resolution 12 bit input impedance 290 k Ω (voltage input) 230-275 k Ω (current input) isolation by group is lower/higher than the range - 5%/+15% maximum error 0.1% Temperature drift voltage: typical value. 70 ppm/° C max. 100 ppm/°C； Current: Type. 50 ppm/° C max.
80 ppm/° C input filter
(Rise time 0-90%) 140ms Update cycle time 8ms Current limiting transmitter power can be limited by MTU Maximum field cable length 600m (656 yards) Maximum input voltage (non-destructive) 30 V DC NMRR, 50Hz, 60Hz>40 dB Rated insulation voltage 50 V Dielectric test voltage 500 V AC. Power consumption 1.5 W current consumption+5 V module bus 70 mA current consumption+24 V module bus 40 mA current consumption+24 V external 0 LED F (failure), R (failure), W (warning) monitoring internal power monitoring status indication module error, module warning, channel error environment and certification CE mark is electrical safety IEC 61131-2, UL 508 hazardous location C1 Div 2 cULus, C1 Zone 2 cULus, ATEX Zone 2 Marine certification ABS, BV, DNV-GL, LR, RS CCS protection level is IP20, in accordance with IEC 60,529 corrosive environment ISA-S71.04 G3 climatic operating conditions 0 to+55 ° C (storage - 40 to+70 ° C), RH=5 to 95% non condensing, IEC/EN 61,131-2 pollution level 2, IEC 60,664-1 mechanical operating conditions IEC/EN 61,131-2 EMC EN 61,000-6-4, EN 61,000-6-2 overvoltage category IEC/EN 60,664-11, EN 50,178 IEC 61,140 Class I equipment; (Grounding protection) The maximum ambient temperature is 55 ° C (131 ° F), which is used for the vertical installation of the compact MTU at 40 ° C (104 ° F). It complies with RoHS directive/2011/65/EU (EN 50581:2012). It complies with WEEE directive/2012/19/EU compatibility and MTU TU810, TU812, TU814, TU818, TU830, TU833, TU835, TU838, TU850. The key code AE size is 45 mm wide (1.77 "), 102 mm deep (4.01"), 111 mm (4.37 inches), Including connector height 119 mm (4.7 inches), weight 0.2 kg (0.44 pounds) 2 Data sheet AI810 | 2019-05-15 | All rights reserved © 2019 ABB Related Products TU810V1 TU812V1 TU824V1 TU830V1 TU833 TU835V1 TU848 TU850 Data Sheet AI820 | May 15, 2019 | All rights reserved
