330500-02-00自动化模块
符合性和认证FCC
此设备符合FCC规则第15部分的要求。操作必须符合以下两个条件：l本设备可能不会造成有害干扰。l此设备必须接受接收到的任何干扰，包括可能导致不期望操作的干扰。EMC EMC指令2014/30/欧盟RoHS RoHS指令2011/65/仅限欧盟海事330400和330425 ABS 2009钢制船舶规则1-1-4/7.7,4-8-3/1.11.1,4-7/13危险区域批准CSA/NRTL/C 190501（机构批准选项01至04）本质安全Ex ia IIC T4：I级，1区，A、B、C、D组II级，E、F和G III级AEx ia IIC T：I级、1区，B、C和D组；II级，E、F、G组III级，根据图纸167536 T4在-40°C下安装≤ 助教≤ +100°C（-40°F≤ 助教≤ +212°F）本质安全和非易燃Ex nL IIC T4 I级2区A、B、C和D组AEx nA T4 I类2区A组B、C、D组根据图纸167536 T4在-40°C下安装≤ 助教≤ +100°C（-40°F≤ 助教≤ +212°F）330400、330425 Ex ia IIC T4 AEx ia IIC T 4 I级，1区A、B、C和D组II级，E、F和G组III级T4@-40°C≤ 助教≤ 100°C根据图纸167538 330500 Ex ia IIC T4 AEx ia IIC T 4 I级，1区，A、B、C和D组II级，E、F、G组III级安装按照图纸167537 T4在-40°C下安装≤ 助教≤ 100°C Ex nL IIC T4 AEx nA IIC T5 I级2区A、B、C、D组根据图纸167537 T4在-40°C下安装≤ 助教≤ 100°C 330525 Ex ia IIC T4 AEx ia IIC T 4 I级，1类，A、B、C和D组II级，E、F、G组III级T4@-40°C≤ 助教≤ 100°C Ex nL IIC T4 AEx nA IIC T5 I级2区A、B、C、D组根据图纸167539 T4在-40°C下安装≤ 助教≤ 100°C ATEX/IECEx 330400和330425加速度传感器数据表4/10 141638 Rev.W 190501、330400、330425、330500、330525 190501实体参数II 1 G Ex ia IIC T4 Ga II 3 D Ex na IIC T5 Gc Ex tc III T130°C Dc T4@Ta=-55°C至121°C区域0/1区域2 Ui=30V Ui=30 V II=200 mA II=200mA Pi=0.75W Pi=1.14W Ci-27.2nF Li=0 330400、430425 330500，330525实体参数II 1 G Ex ia IIC T4 Ga II 3 D Ex na IIC T6 Gc Ex tc III T130°C Dc T4@Ta=-55°C至121°C 0/1区2 Ui=28V Ui=28 V II=150 mA II=150mA Pi=0.84W Pi=1.26W Ci-10.8nF Li=0
危险区域安全使用条件
ATEX/IECEx 0/1区：设备必须连接到符合上述实体参数的设备。A或B型电缆（符合EN 60079-25）必须符合实体参数中列出的电缆参数。区域2：电源电气参数不得超过上表中提到的值。330400和330425加速计加速度传感器数据表5/10 141638版本W订购信息有关国家和产品特定批准的详细列表，请参阅Bently.com上的批准快速参考指南，文件108M1756。330400加速计330425加速计零件号AA BB A：安装螺纹选项0 1¼-28 UNF整体螺柱0 2 M8 X 1整体螺柱B：机构批准选项0 0无0 5多重批准（CSA、ATEX、IECEx）互连电缆零件号AA A：电缆长度选项（英尺）对于以下列出的电缆，订购增量为1.0英尺（305 mm）。示例：1 5=15英尺（4.57米）2 0=20英尺（6.10米）以下为标准长度英尺米（约）6 1.8 8 2.4 10 3.0 12 3.6 15 4.5 17 5.0 20 6.0 25 7.6 30 9.0 33 10.0 50 15.2 99 30.0也可额外订购非标准/定制长度。电缆零件号130539 3芯屏蔽18 AWG（1.0 mm2）电缆，一端带有3插座插头和氟硅橡胶护套，另一端带有接线片。最小长度为2.0英尺（0.6米），最大长度为99英尺（30米）。有手册可帮助安装该电缆（零件号133080-01）。16925 3芯屏蔽22 AWG（0.5 mm2）电缆，一端带3插座插头，另一端带接线片。最小长度为2.0英尺（0.6米），最大长度为99英尺（30米）。16710 3芯屏蔽22 AWG（0.5 mm2）铠装电缆，一端带3插座插头，另一端带接线片。最小长度为3.0英尺（0.9米），最大长度为99英尺（30米）。附件127088-01 330400和330425加速计操作手册。00531080用于330400和330425加速计的匹配连接器。37439-01用于序列号前不带字母“G”的情况。安装底座，¼-28至¼-28.降低底座应变敏感性。37439-02用于序列号前不带字母“G”的情况。安装底座，M8X1至M8X1.降低底座应变敏感性。43217加速计安装套件，用于延伸件零件号108576-01和O形圈零件号04290422，以便为
Compliance and Certification FCC
This device complies with the requirements of Part 15 of the FCC Rules. Operation must meet the following two conditions: l This equipment may not cause harmful interference. L This equipment must accept any interference received, including interference that may cause undesired operation. EMC EMC Directive 2014/30/EU RoHS RoHS Directive 2011/65/EU Maritime 330400 and 330425 ABS 2009 Steel Ship Rules 1-1-4/7.7, 4-8-3/1.11.1, 4-7/13 Hazardous Area Approval CSA/NRTL/C 190501 (Agency Approval Options 01 to 04) Intrinsic Safety Ex ia IIC T4: Class I, Zone 1, Groups A, B, C, D Class II, E, F and G Class III AEx ia IIC T: Class I, Zone 1, Groups B, C and D; Class II, Groups E, F, G Class III, installed at - 40 ° C according to drawing 167,536 T4 ≤ teaching assistant ≤+100 ° C (- 40 ° F ≤ teaching assistant ≤+212 ° F) Intrinsically safe and non flammable Ex nL IIC T4 Class I, Division 2, Groups A, B, C, and D AEx nA T4 Class I, Division 2, Group A, Groups B, C, and D installed at - 40 ° C according to drawing 167,536 T4 ≤ teaching assistant ≤+100 ° C (- 40 ° F ≤ teaching assistant ≤+212 ° F) 330,400, 330,425 Ex ia IIC T4 AEx ia IIC T 4 Class I, Zone 1, Groups A, B, C, and D, Class II, E Groups F and G Class III T4@-40 ° C ≤ teaching assistant ≤ 100 ° C According to drawing 167538 330500 Ex ia IIC T4 AEx ia IIC T4 Class I, Zone 1, Groups A, B, C and D Class II, Groups E, F and G Class III Installation according to drawing 167537 T4 Installation at - 40 ° C ≤ teaching assistant ≤ 100 ° C Ex nL IIC T4 AEx nA IIC T5 Class I, Zone 2 Groups A, B, C and D Installation at - 40 ° C according to drawing 167537 T4 ≤ teaching assistant ≤ 100 ° C 330525 Ex ia IIC T4 AEx ia IIC T4 Class I, Class 1, Groups A, B, C, and D, Class II, E, F Group G Grade III T4@-40 ° C ≤ TA ≤ 100 ° C Ex nL IIC T4 AEx nA IIC T5 Class I, Zone 2, Groups A, B, C, D are installed at - 40 ° C according to drawing 167539 T4 ≤ TA ≤ 100 ° C ATEX/IECEx 330400 and 330425 acceleration sensor data sheet 4/10 141638 Rev. W 190501, 330400, 330425, 330500, 330525 190501 Real parameter II 1 G Ex ia IIC T4 Ga II 3 D Ex na IIC T5 Gc Ex tc III T130 ° C Dc T4@Ta =-55 ° C to 121 ° C Zone 0/1 Zone 2 Ui=30V Ui=30 V II=200 mA II=200mA Pi=0.75W Pi=1.14W Ci-27.2nF Li=0 330400, 430425 330500330525 Entity parameters II 1 G Ex ia IIC T4 Ga II 3 D Ex na IIC T6 Gc Ex tc III T130 ° C Dc T4@Ta =-55 ° C to 121 ° C Zone 0/1 2 Ui=28V Ui=28V II=150 mA II=150mA Pi=0.84W Pi=1.26W Ci-10.8nF Li=0
Conditions for safe use in hazardous areas
ATEX/IECEx Zone 0/1: The equipment must be connected to the equipment meeting the above entity parameters. Type A or B cables (according to EN 60079-25) must conform to the cable parameters listed in the physical parameters. Zone 2: The electrical parameters of the power supply shall not exceed the values mentioned in the above table. 330400 and 330425 Accelerometer Accelerometer Sensor Data Sheet 5/10 141638 Version W Ordering Information For a detailed list of country and product specific approvals, see Bently Quick Reference Guide for Approvals on. com, document 108M1756. 330400 Accelerometer 330425 Accelerometer Part Number AA BB A: Mounting Thread Option 0 1 ¼- 28 UNF integral stud 0 2 M8 X 1 integral stud B: Agency approved option 0 0 None 0 5 Multiple approvals (CSA, ATEX, IECEx) Interconnect cable part number AA A: Cable length option (feet) For the cables listed below, order in increments of 1.0 feet (305 mm). Example: 1 5=15 feet (4.57 meters) 2 0=20 feet (6.10 meters) below is the standard length feet meters (approximately) 6 1.8 8 2.4 10 3.0 12 3.6 15 4.5 17 5.0 20 6.0 25 7.6 30 9.0 33 10.0 50 15.2 99 30.0 Additional non-standard/custom lengths can also be ordered. Cable part number 130539 3-core shielded 18 AWG (1.0 mm2) cable with a 3-socket plug and fluorosilicone rubber sheath at one end and a lug at the other end. The minimum length is 2.0 feet (0.6 meters) and the maximum length is 99 feet (30 meters). A manual is available to help install the cable (part number 133080-01). 16925 3-core shielded 22 AWG (0.5 mm2) cable with 3 socket plugs at one end and lug at the other end. The minimum length is 2.0 feet (0.6 meters) and the maximum length is 99 feet (30 meters). 16710 3-core shielded 22 AWG (0.5 mm2) armored cable with 3 socket plugs at one end and lug at the other end. The minimum length is 3.0 feet (0.9 meters) and the maximum length is 99 feet (30 meters). Attachment 127088-01 330400 and 330425 Accelerometer Operation Manual. 00531080 is used for matching connector of 330400 and 330425 accelerometers. 37439-01 is used when there is no letter "G" before the serial number. Mounting base, ¼- 28 to ¼- 28. Reduce the base strain sensitivity. 37439-02 is used when there is no letter "G" before the serial number. Mount the base, M8X1 to M8X1. Reduce the base strain sensitivity. 43217 Accelerometer mounting kit for extension part number 108576-01 and O-ring part number 04290422 to
