M2004HW 卡板
电源循环
高级用户参数保存在非易失性存储器中。CHPARM命令所做的更改将在重新启动和关闭电源后保留，直到CHPARM再次更改。4.要永久更改Station Manager密码，必须更改AUP文件中的stpasswd参数。有关详细信息，请参阅《TCP/IP Ethernet Communications for PACSystems用户手册》GFK-2224。（CPU配置存储到CPU中后，CHPARM命令被禁止，之前对其所做的任何更改都不再有效。）在使用以太网通信之前，需要配置IP地址。在配置有效IP地址之前，以太网接口无法在网络上运行。必须在实际网络操作之前配置以太网寻址信息，或从Ethernet接口上的以太网寻址数据的意外更改中恢复。使用以下方法之一初始分配IP地址：▪ 将串行终端连接到接口的Station Manager端口。然后使用CHSOSW命令输入所需的IP地址。有关详细信息，请参阅PACSystems TCP/IP Communications Station Manager Manual，GFK-2225。▪ 通过以太网使用SetIP工具临时为模块分配IP地址。有关详细信息，请参阅用于PACSystems的TCP/IP以太网通信，GFK-2224。▪ Ethernet接口自动从网络上的BOOTP服务器获取临时IP地址。有关详细信息，请参阅用于PACSystems的TCP/IP以太网通信，GFK-2224。一旦设置了临时IP地址，就可以通过网络访问以太网接口（通过机器版编程软件）。
应使用编程器
为Ethernet接口配置正确的IP地址。默认IP地址（0.0.0.0）尝试通过BOOTP设置IP地址默认IP地址值（0.0.0.0.0），无论是从硬件配置还是备份配置获得，都会导致Ethernet接口从网络上的BOOTP服务器设备请求临时IP地址。LAN必须是树型，而不是环形。PACSystems RX3i以太网接口上的两个以太网端口不得直接或间接连接到同一网络设备。以太网中的集线器或交换机连接必须形成树而不是环；否则可能导致分组重复和网络过载。在这种情况下，RX3i以太网模块将持续复位。重复IP地址的报告当PACSystems RX3i在网络上检测到重复IP地址时，它不会在控制器故障表中记录异常或故障。RX3i以太网接口模块IPI IC695ETM001-JX 2017年11月13日GFK-2332Z以太网操作说明主题描述多个零周期EGD交换机可能不会产生相似数量的样本如果为零生产周期配置了多个EGD交换机，则交换机可能不会产生相似数量的采样。由于当多个交换被“尽可能快地”调度时，调度发生的方式，一些零周期
Power is cycled
Advanced user parameters are stored in non-volatile memory. Changes made by the CHPARM command are retained after rebooting and powering down until CHPARM changes again. 4. To permanently change the Station Manager password, you must change the stpasswd parameter in the AUP file. For more information, see TCP/IP Ethernet Communications for PACSystems User Manual GFK-2224. (After the CPU configuration is stored in the CPU, the CHPARM command is disabled, and any changes made to it before are no longer valid.) Before using Ethernet communication, you need to configure the IP address. The Ethernet interface cannot run on the network until a valid IP address is configured. Ethernet addressing information must be configured before actual network operation, or recovered from unexpected changes in Ethernet addressing data on the Ethernet Interface. Use one of the following methods to initially assign an IP address: ▪ Connect the serial terminal to the Station Manager port of the interface. Then use the CHSOSW command to enter the desired IP address. For more information, see PACSystems TCP/IP Communications Station Manager Manual, GFK-2225. ▪ Use the SetIP tool to temporarily assign IP addresses to modules over Ethernet. For more information, see TCP/IP Ethernet Communication for PACSystems, GFK-2224. ▪ The Ethernet interface automatically obtains the temporary IP address from the BOOTP server on the network. For more information, see TCP/IP Ethernet Communication for PACSystems, GFK-2224. Once the temporary IP address is set, the Ethernet interface can be accessed through the network (through the machine version programming software).
Programmer shall be used
Configure the correct IP address for the Ethernet Interface. The default IP address (0.0.0.0) attempts to set the default IP address value (0.0.0.0.0) of the IP address through BOOTP. Whether obtained from the hardware configuration or the backup configuration, the Ethernet interface will request a temporary IP address from the BOOTP server device on the network. The LAN must be tree, not ring. The two Ethernet ports on the PACSystems RX3i Ethernet interface must not be directly or indirectly connected to the same network device. The hub or switch connection in Ethernet must form a tree rather than a ring; Otherwise, packet duplication and network overload may be caused. In this case, the RX3i Ethernet module will continue to reset. Duplicate IP Address Report When PACSystems RX3i detects duplicate IP addresses on the network, it will not record exceptions or faults in the controller fault table. RX3i Ethernet interface module IPI IC695ETM001-JX, November 13, 2017, the topic of GFK-2332Z Ethernet Operating Instructions describes that multiple zero cycle EGD switches may not generate a similar number of samples. If multiple EGD switches are configured for zero production cycle, the switches may not generate a similar number of samples. When multiple exchanges are scheduled "as soon as possible", the scheduling occurs in a way that has zero cycles
