CI625 变频器
处于默认位置
这允许IC697 CPU JP10和JP55在默认位置激活SYSFAIL信号。此跳线将插槽1中的LWORD/信号跳线为非激活状态，仅允许16位宽的数据传输。所有其他跳线均保持在出厂设置的默认位置（2）IC697/VME配置此配置包括插槽PL3和PL11中的IC697 CPU或总线接收器模块以及IC697模块和VME模块的组合，包括剩余插槽中的第三方VME。IC697模块只能放置在插槽PL5至PL8和PL13至PL16中。VME模块可以使用VME插槽PL5至PL9和PL13至PL17。请注意，所有插槽都有一个跳线，允许您禁用7个冗余机架、前安装和后安装GFK-1447B PLC机架2000年1月通过移除适当的跳线向该插槽发送SYFAIL/信号。注：第三方模块的集成必须符合《第三方VME模块集成用户指南》中所述的指南。IC697/VME跳线位置机架ID跳线JP1-JP4（左侧）和JP46-JP49（右侧）跳线到机架ID的正确位置。Sysfail跳线（见表2）保持在默认位置（出厂时）。这允许IC697 CPU激活SYSFAIL/信号（IC697 I/O模块需要SYSFAIL）。JP10和JP55保持在其默认位置。这将插槽1中的LWORD/信号跳转为非激活状态（对于IC697模块），仅允许16位宽的数据传输。如果使用信号IRQ1/-IRQ4/的IC697模块安装在插槽PL5至PL8（左侧）或PL13至PL16（右侧）中，则您必须在使用中IC697插槽最左边的位置安装最多四个跳线（视情况而定）。空白插槽中断跳线必须安装在未使用的插槽中。
备用插槽
跳线JP11和JP56为总线授权和IACK信号提供了一条穿过未使用的备用插槽PL4和PL12的路径，并且应该保持在适当的位置。（3） VME配置此配置由插槽PL3或PL11中的第三方控制器和剩余插槽中的第3方VME模块组成。请注意，每个插槽都有一个跳线，允许禁用该插槽的SYSFAIL/信号，因为所有VME模块可能不需要访问该信号。电源延长电缆对于需要两个机架的应用，一个电源可能足以为两个机架供电。只有当第二个机架需要+5伏、5.2安培或更低的电压时，才能从单个电源实现这种双机架操作。使用此方法无法为第二个机架提供±12伏电压，因为电源延长电缆不提供与这些电压的连接。注意：尽管此冗余机架中有两个电源，但第二个机架的电源仅由最左侧的电源提供支持。最右侧的电源将不向第二个机架供电。提供了一根3英尺长的电源延长电缆（参见本数据表最后一页的订购信息），可提供必要的互连。除了+5伏电源外，延长电缆还包括以下所需的电源顺序信号
In default position
This allows IC697 CPUs JP10 and JP55 to activate SYSFAIL signals in the default position. This jumper deactivates the LWORD/signal jumper in slot 1, allowing only 16 bit wide data transmission. All other jumpers remain in the factory default position (2) IC697/VME configuration This configuration includes the IC697 CPU or bus receiver module in slots PL3 and PL11 and the combination of IC697 module and VME module, including third-party VMEs in the remaining slots. IC697 modules can only be placed in slots PL5 to PL8 and PL13 to PL16. VME modules can use VME slots PL5 to PL9 and PL13 to PL17. Note that all slots have a jumper that allows you to disable the seven redundant racks, front mounted and rear mounted GFK-1447B PLC racks in January 2000 by removing the appropriate jumper to send SYFAIL/signals to that slot. Note: The integration of third-party modules must comply with the guidelines described in the Third Party VME Module Integration User Guide. IC697/VME jumper location Rack ID jumpers JP1-JP4 (left side) and JP46-JP49 (right side) jumper to the correct location of the Rack ID. Sysmail jumper (see Table 2) remains in the default position (when leaving the factory). This allows the IC697 CPU to activate the SYSFAIL/signal (the IC697 I/O module requires SYSFAIL). JP10 and JP55 remain in their default positions. This switches the LWORD/signal in slot 1 to inactive (for IC697 modules), allowing only 16 bit wide data transmission. If the IC697 module using the signal IRQ1/- IRQ4/is installed in slots PL5 to PL8 (left side) or PL13 to PL16 (right side), you must install up to four jumpers in the leftmost position of the IC697 slot in use, as appropriate. The blank slot interrupt jumper must be installed in an unused slot.
Spare slot
Jumpers JP11 and JP56 provide a path through unused spare slots PL4 and PL12 for bus authorization and IACK signals, and should remain in place. (3) VME ConfigurationThis configuration consists of third-party controllers in slots PL3 or PL11 and third-party VME modules in the remaining slots. Note that each slot has a jumper that allows disabling the SYSFAIL/signal for that slot because all VME modules may not need to access the signal. Power Extension Cable For applications that require two racks, one power supply may be sufficient to power both racks. This dual rack operation can only be achieved from a single power source when the second rack requires+5 volts, 5.2 amps, or less. It is not possible to supply ± 12 volts to the second rack using this method because the power extension cable does not provide a connection to these voltages. Note Although there are two power supplies in this redundant rack, the power supply for the second rack is only supported by the leftmost power supply. The rightmost power supply will not supply power to the second rack. A 3-foot power extension cable (see ordering information on the last page of this data sheet) is provided to provide the necessary interconnections. In addition to the+5V power supply, the extender cable includes the following required power sequence signals
