DDO02 自动化模块
机器电压
UNITROL 1020的本地人机界面提供AVR状态的即时数据。显示器显示默认操作模式、机器电压和励磁机电流软键按钮功能根据活动菜单箭头导航菜单或设置参数UNITROL 1010是一种支持UNITROL1020子集的紧凑型设备，设计用于额定电流高达10 a的励磁电流。它支持与UNITROL 1020相同的接口，并具有相同的机械占地面积。UNITROL1005是最紧凑的UNITROL1000设备，设计用于额定电流高达5A的励磁电流。模拟和数字输入和输出•拉伸弹簧端子允许可靠的以太网端口布线•连接CMT1000•通过Modbus TCP USB端口远程访问•连接CMT2000（调试和维护工具）指示LED•操作指示实心铝基板•坚固的机械设计允许在高振动应用中使用电源和测量端子•规定的最大持续电流为30 A，电缆最大为4 mm2（AWG 24–10）•用于可靠连接的拉簧端子•易于接近测试点UNITROL 1010和UNITRO 1020 UNITROL 1005硬件类型概述。，55°C环境温度下25 A上限20 A续，55°C温度下38 A上限。辅助电源的独立端子否是是人机接口否是模拟和数字I/O•数字：4个输出，8个输入•模拟：2个输出•数字：8个I/O，4个输入•模拟：3个输入，2个输出？数字：8输入，4个输出•模拟：3个输出，2个输出接口•USB•以太网•USB•RS485/（CAN）•以太网•USB•RS488/（CAN
电力电子输入
（AC/DC）AC标称输入电压16至250 VAC 0至250 VAC 0至250 VAC频率25至600 Hz 25至600赫兹DC标称输入电压18至300 VDC 0至300 VDC最大峰值输入电压（非正弦）420 VP 420 VPP最小所需启动电压6VAC/10 VDC N/A辅助电源（控制器）输入AC标称输入3相非支持9至250 VAC 9至250 V AC标称输入电压1相不支持16至250 V C 16至250 VAC频率不支持40至600 Hz 40至600赫兹DC标称输入电压不支持18至300 VDC 18至300 V直流最大峰值输入电压（非正弦）不支持420 VP 420 VP励磁输出55°C时的连续电流8 ADC 10 ADC 15 ADC 20 ADC 1）10的过载电流秒55°C 16ADC 25 ADC 38 ADC励磁机电流测量全范围0至25 A 0至38 A 0至38A精度/分辨率<1%/<20 mA<1%/<100 mA<1%/<100 mA机器和净测量机器电压，1、2或3相，最高500 VAC 2）最高500 VAC 2）机器电流，1相1至5 AAC 1至5 AAC 1至5AAC网络电压，单相，最高500 VAC，最高500 V，最高500 VAC，频率范围10至150 Hz，10至150赫兹，10至150Hz，准确度（-40°至70°C/25°C）±1%/0.1%±1%±0.1%电压调节AVR响应时间（三相/单相测量。)<20 ms/<50 ms<20 ms/<50 ms<20 ms/<50 ms PWM限制0.5至99%0.5至99%0.5%至99%数字输入和输出数字输入/输出仅输入/输入/输出8/0/4 4/8/0 4/8/0数字IO电压24 V 24 V模拟输入和输出模拟输入/输出数量2/0 3/2 3/2模拟IO范围±10 V/0…20 mA±10 V±10V通信接口以太网（电缆长度<100 m）10/100 MBit/s 10/100 MBit/s 10/100 MBit/s USB版本（电缆长度<3 m）1.0；1.1; 2.0 1.0; 1.1; 2.0 1.0; 1.1; 不支持2.0 CAN（电缆长度<3 m）仅用于UNITROL 1000设备之间的连接仅用于UNITROL 1000之间的连接
Machine voltage
The local human-machine interface of UNITROL 1020 provides real-time data of AVR status. The display shows the default operating mode, machine voltage and exciter current soft key button functions. The UNITROL 1010 is a compact device that supports a subset of UNITROL 1020 and is designed for excitation currents with rated currents up to 10 a, depending on the active menu arrow navigation menu or setting parameters. It supports the same interface as UNITROL 1020 and has the same mechanical floor area. UNITROL1005 is the most compact UNITROL1000 device, designed for excitation current with rated current up to 5A. Analog and digital inputs and outputs • Tension spring terminals allow reliable Ethernet port wiring • Connect CMT1000 • Remote access via Modbus TCP USB port • Connect CMT2000 (commissioning and maintenance tools) indication LED • Operation indication solid aluminum substrate • Rugged mechanical design allows power and measurement terminals to be used in high vibration applications • The specified maximum continuous current is 30 A, The maximum cable size is 4 mm2 (AWG 24 – 10) • Tension spring terminals for reliable connection • Easy access to test points UNITROL 1010 and UNITROL 1020 UNITROL 1005 Hardware type overview., 25 A upper limit 20 A at 55 ° C ambient continued, 38 A upper limit at 55 ° C. Whether the independent terminal of auxiliary power supply is man-machine interface or analog and digital I/O • Digital: 4 outputs, 8 inputs • Analog: 2 outputs • Digital: 8 I/Os, 4 inputs • Analog: 3 inputs, 2 outputs? Digital: 8 inputs, 4 outputs • Analog: 3 outputs, 2 output interfaces • USB • Ethernet • USB • RS485/(CAN) • Ethernet • USB • RS488/(CAN
Power electronic input
(AC/DC) AC nominal input voltage 16 to 250 VAC 0 to 250 VAC 0 to 250 VAC frequency 25 to 600 Hz 25 to 600 Hz DC nominal input voltage 18 to 300 VDC 0 to 300 VDC maximum peak input voltage (non sinusoidal) 420 VP 420 VPP minimum required starting voltage 6VAC/10 VDC N/A auxiliary power supply (controller) Input AC nominal input 3-phase unsupported 9 to 250 VAC 9 to 250 V AC nominal input voltage 1-phase unsupported 16 to 250 V C 16 to 250 VAC frequency unsupported 40 to 600 Hz 40 to 600 Hz DC nominal input voltage unsupported 18 to 300 VDC 18 to 300 V DC maximum peak input voltage (non sinusoidal) 420 VP 420 VP excitation output continuous current at 55 ° C 8 ADC 10 ADC 15 ADC 20 ADC 1) 10 overload current seconds 55 ° C 16ADC 25 ADC 38 ADC exciter current measurement full range 0 to 25 A 0 to 38 A 0 to 38 A accuracy/resolution<1%/<20 mA<1%/<100 mA<1%/<100 mA machine and net measured machine voltage, 1, 2 or 3 phases, up to 500 VAC 2) up to 500 VAC 2) machine current, 1 phase 1 to 5 AAC 1 to 5 AAC 1 to 5 AAC 1 to 5AAC network voltage, single-phase, Up to 500 VAC, up to 500 V, up to 500 VAC, frequency range 10 to 150 Hz, 10 to 150 Hz, 10 to 150 Hz, accuracy (- 40 ° to 70 ° C/25 ° C) ± 1%/0.1% ± 1% ± 0.1% voltage regulation AVR response time (three-phase/single-phase measurement)< 20 ms/<50 ms<20 ms/<50 ms<20 ms/<50 ms PWM limit 0.5 to 99% 0.5 to 99% 0.5 to 99% digital input and output digital input/output only input/input/output 8/0/4 4/8/0 4/8/0 digital IO voltage 24 V 24 V analog input and output analog input/output quantity 2/0 3/2 3/2 analog IO range ± 10 V/0... 20 mA ± 10 V ± 10V communication interface Ethernet (cable length<100 m) 10/100 MBit/s 10/100 MBit/s USB version (cable length<3 m) 1.0； 1.1; 2.0 1.0; 1.1; 2.0 1.0; 1.1; 2.0 CAN (cable length<3 m) is not supported. It is only used for connection between UNITROL 1000 devices. It is only used for connection between UNITROL 1000 devices
