输入输出模块DSMC112 57360001-HC控制器
低泄漏输入/输出模块
是一个智能、可配置的模块，将离散传感器和执行器连接到通信总线。该模块有八个相同的115VAC电路。每个电路可以用作输入或输出。115V 50/60 Hz输入/输出功能块功能包括：可选择输入滤波时间，从10ms到100ms。用于监控的输出反馈。输出通电默认值。输出保持最后的状态或默认值。输出脉冲测试。总线开关模块控制。模块的控制电源由连接到端子的输入/输出设备电压分接。不需要单独的块电源。每个电路都有电子熔断器，如果输出电流超过30安培且输出接通，则在5毫秒内关闭电路，或在2个循环后关闭20安培。通过手持监视器或CPU发出的命令，电路很容易恢复。块诊断包括：三态输入的过热故障开关开路过载检测和停机空载检测故障报告可按电路启用或禁用。使用本数据表_本数据表总结了有关块安装、配置和诊断的信息。您的主要参考应为《离散和模拟块用户手册》。它包括块安装和配置的详细说明。有关系统和通信的更多信息，包括总线规格，请参阅I/O系统和通信手册。规格目录号块电子组件IC66*EBD101端子组件IC66*TSD100块规格尺寸（高x宽x深）8.83”（22.44cm）x 3.34”（8.48cm）x 3.91”（9.93cm）重量4磅（1.8 kg）LED（I/O块）单元正常，I/O启用LED（每个电路）开关块到块隔离的逻辑侧最大1500V散热16W，8个输入，最大43.5W，8输出，2安培。
备用电源
（所有输入和输出均关闭）8.5瓦工作电压（单电源）93-132VAC频率47-63 Hz电源断开时间1个周期（60Hz时为16.7ms，50Hz时为20ms）输入规格非三态输入断开状态输入设备的最小电压（IN到H）60V RMS断开状态，输入设备的最大泄漏1.5mA接通状态，输入设备两端的最大电压（IN到H）20V RMS ON状态，最大开关电流阈值6mA RMS Tristate输入OFF状态，输入设备两端可接受的电压（IN至H）16V RMS-40V RMS，ON状态，输入设备两端的最大电压（IN到H）4V RMS输入负载网络电阻器到N：13K欧姆电容器到H：0.10µf输入处理时间（典型）2ms+滤波器可选择输入滤波器时间10到100ms，以10ms为增量输入诊断开路、超温、，故障开关输出规格电路输出电流（稳态）2安培RMS最大涌流高达2个周期25安培峰值涌流2-6个周期14安培峰值最大阻塞输出电流15安培（35°C），60°C时7.5安培输出泄漏@115 VAC时0伏输出（OUT到N）时的电流：<7mA开路输出（OUT-N）时电压：65伏输出开关（OFF到ON/ON到OFF）零交叉最大开关频率每秒一次（高涌入电流）开启延迟0.5 Hz+1ms，2安培时最大压降2.5V，30安培时10V涌入推荐最小负载（空载禁用）25mA电阻，40mA感应空载启用阈值50mA保险丝内部电子短路跳闸。100ms长时间跳闸输出诊断短路、过载、空载、开关故障、超温环境规范工作温度0°C至+60°C（+32°至+140°F）存储温度-40°至+100°C（-40°到+212°F）湿度5%至95%（非冷凝）振动5-10 Hz 0.2“（5.08mm）位移，1G下10-200 Hz参考GFK-0867了解产品标准和一般规范
Low leakage I/O module
Is an intelligent, configurable module that connects discrete sensors and actuators to the communications bus. The module has eight identical 115VAC circuits. Each circuit can be used as an input or output. 115V 50/60 Hz input/output function block functions include: selectable input filtering time, from 10ms to 100ms. Output feedback for monitoring. Output power on default value. The output remains the last state or default value. Output pulse test. Bus switch module control. The control power supply of the module is tapped by the input/output device voltage connected to the terminal. No separate block power supply is required. Each circuit has an electronic fuse. If the output current exceeds 30 amperes and the output is on, close the circuit within 5 milliseconds, or close 20 amperes after 2 cycles. The circuit can be easily recovered through the command issued by the handheld monitor or CPU. Block diagnosis includes: the open circuit overload detection and shutdown no-load detection fault report of the three state input overheating fault switch can be enabled or disabled according to the circuit. Use this data sheet_ This data sheet summarizes information about block installation, configuration, and diagnostics. Your main reference should be the Discrete and Analog Block User's Manual. It includes detailed instructions for block installation and configuration. For more information about the system and communications, including bus specifications, refer to the I/O System and Communications manual. Specification Catalog No. Block Electronic assembly IC66 * EBD101 Terminal assembly IC66 * TSD100 Size (H x W x D) 8.83 "(22.44cm) x 3.34" (8.48cm) x 3.91 "(9.93cm) Weight 4 pounds (1.8 kg) LED (I/O block) unit is normal, I/O enabled LED (each circuit) switch block to block isolated logic side, maximum 1500V heat dissipation 16W, 8 inputs, maximum 43.5W, 8 outputs, 2 amps.
emergency power supply
(All inputs and outputs are turned off) 8.5 W working voltage (single power supply) 93-132VAC frequency 47-63 Hz power off time 1 cycle (16.7ms at 60Hz, 20ms at 50Hz) input specification non three state input off state minimum voltage of input device (IN to H) 60V RMS off state, maximum leakage of input device 1.5mA on state, maximum voltage at both ends of input device (IN to H) 20V RMS ON state, The maximum switching current threshold value is 6mA RMS Tristate. Input the OFF state, the acceptable voltage at both ends of the input device (IN to H) 16V RMS - 40V RMS, the ON state, the maximum voltage at both ends of the input device (IN to H) 4V RMS input load network resistor to N: 13K ohm capacitor to H: 0.10 µ f input processing time (typical) 2ms+filter can select the input filter time of 10 to 100ms. Input the diagnosis of open circuit, overtemperature, Fault Switch Output Specifications Circuit Output Current (Steady State) 2 Amps RMS Maximum Inrush Up to 2 Cycles 25 Amps Peak Inrush 2-6 Cycles 14 Amps Peak Blocking Output Current 15 Amps (35 ° C) Maximum, 7.5 A output leakage at 60 ° C @ 1 Current at 0 V output (OUT to N) at 15 VAC:<7 mA Voltage at open circuit output (OUT-N): 65 V Output switch (OFF to ON/ON to OFF) Zero crossover Maximum switching frequency once per second (high inrush current) Opening delay 0.5 Hz+1 ms, maximum voltage drop 2.5 V at 2 A, 10 V inrush at 30 A Recommended minimum load (no load disabled) 25 mA resistance, 40mA inductive no-load enabling threshold 50mA fuse internal electronic short circuit trip. 100ms long trip output diagnosis short-circuit, overload, no-load, switch fault, overtemperature Environmental specification Operating temperature 0 ° C to+60 ° C (+32 ° to+140 ° F) Storage temperature - 40 ° to+100 ° C (- 40 ° to+212 ° F) Humidity 5% to 95% (non condensing) Vibration 5-10 Hz 0.2 "(5.08mm) Displacement, 10-200 Hz under 1G Refer to GFK-0867 for product standards and general specifications
