DSMB133 57360001-CY 工控备件
可配置模块
说明115VAC离散输入模块是一个智能、可配置模块，为115VAC分立输入传感器提供接口。该模块有16个115VAC电路-两组，每组8个电路。该模块的典型输入是来自开关、按钮或限位开关的触点闭合。该模块可用于2线和3线接近开关输入。块的控制电源来自提供输入的电源线。不需要单独的块电源。115V 50/60 Hz输入功能块功能包括：可选阈值高级诊断软件可配置功能16路115 VAC输入块可配置检测开路和短路故障。可选择的阈值将开路和/或短路诊断的使用扩展到具有多种类型输入设备和传感器的电路。每组八个输入有单独的开/关阈值。开/关阈值可配置为输入线电压的25%至85%，允许使用各种输入传感器。可以为单个输入选择可选的开路检测。开/关阈值也可以配置为输入线电压的25%至85%。可以为每组八个输入选择单独的打开/关闭阈值。也可以为单个输入选择10%和90%进线电压下的可选短路检测。对于大多数应用，默认阈值和推荐电阻值不会更改。
故障报告
也可以按电路启用或禁用。规格目录号块类型16电路，仅输入块IC66*BBD110电子组件IC66*EBD110端子组件IC66*TBD110块规格尺寸（高x宽x深）8.83”（22.44cm）x 3.34”（8.48cm）x 3.91”（9.93cm）重量4磅（1.8 kg）LED（I/O块）单元正常，I/O启用LED（每个电路）反映输入状态（逻辑侧）输入到接地或串行总线隔离1500V散热最大28瓦，16个输入在全电流下打开工作电压（单电源）93-132VAC频率47-63 Hz所需功率（仅限块）80mA最大块电流加200mA最大输入电路电流端子板额定值（输入或馈通电流）5.0安培电源断开时间1周期（60Hz时为16.7ms，50Hz时为20ms）输入规格输入关闭状态，输入开启状态可编程阈值（25%至85%）输入阻抗（典型值）11.6K欧姆输入开路可编程阈值，短路环境规范工作温度0°C至+60°C（+32°至+140°F）储存温度-40°C至+100°C（-40°至+212°F）湿度5%至95%（非冷凝）振动5-10 Hz 0.2“（5.08mm）位移，1G下10-200 Hz参考GFK-0867了解产品标准和一般规范。使用本数据表_本数据表总结了有关块安装、配置和诊断的信息。您的主要参考应为《离散和模拟块用户手册》。它包括块安装和配置的详细说明。有关系统和通信的更多信息，包括总线规格，请参阅I/O系统和通信手册。
Configurable module
It shows that 115VAC discrete input module is an intelligent and configurable module, which provides interface for 115VAC discrete input sensor. The module has 16 115VAC circuits - two groups of 8 circuits each. A typical input to this module is contact closure from a switch, button, or limit switch. The module can be used for 2-wire and 3-wire proximity switch inputs. The control power for the block comes from the power cord that provides the input. No separate block power supply is required. Functions of 115V 50/60 Hz input function block include: optional threshold, advanced diagnostic software, configurable function, 16 channel 115 VAC input block, configurable detection of open circuit and short circuit faults. Selectable thresholds extend the use of open circuit and/or short circuit diagnostics to circuits with multiple types of input devices and sensors. Each group of eight inputs has a separate on/off threshold. The on/off threshold can be configured at 25% to 85% of the input line voltage, allowing the use of various input sensors. Optional open circuit detection can be selected for a single input. The on/off threshold can also be configured as 25% to 85% of the input line voltage. Individual on/off thresholds can be selected for each set of eight inputs. Optional short circuit detection at 10% and 90% incoming line voltage can also be selected for a single input. For most applications, the default threshold and recommended resistance values do not change.
Fault report
It can also be enabled or disabled by circuit. Specification catalog No. Block type 16 circuit, only input block IC66 * BBD110 electronic assembly IC66 * EBD110 terminal assembly IC66 * TBD110 specification size (H x W x D) 8.83 "(22.44cm) x 3.34" (8.48cm) x 3.91 "(9.93cm) weight 4lb (1.8 kg) LED (I/O block) unit is normal, I/O enable LED (each circuit) reflects input status (logic side) Input to ground or serial bus isolation 1500V Heat dissipation maximum 28W, 16 inputs open working voltage under full current (single power supply) 93-132VAC frequency 47-63 Hz required power (only for blocks) 80mA maximum block current plus 200mA maximum input circuit current Terminal board rating (input or feed through current) 5.0 Amp Power off time 1 cycle (16.7ms at 60Hz, 20ms at 50Hz) Input specification Input closed state, Input open state programmable threshold (25% to 85%) Input impedance (typ.) 11.6K Ohms Input open circuit programmable threshold, Short circuit environment specification Operating temperature 0 ° C to+60 ° C (+32 ° to+140 ° F) Storage temperature - 40 ° C to+100 ° C (- 40 ° to+212 ° F) Humidity 5% to 95% (non condensing) Vibration 5-10 Hz 0.2 "(5.08mm) Displacement, 10-200 Hz at 1G Refer to GFK-0867 for product standards and general specifications. Use this datasheet _ this datasheet to summarize information about block installation, configuration and diagnosis. Your main reference should be Discrete and Analog Block User's Manual 。 It includes detailed instructions for block installation and configuration. For more information about the system and communications, including bus specifications, refer to the I/O System and Communications manual.
