6230BP10830A-A 工控模块系统备件
可配置数据和程序存储器
RX7i CPU由编程软件编程和配置，以实时控制机器、工艺和材料处理系统。CPU使用VME64标准格式通过机架安装的背板与I/O和智能选件模块通信。它通过嵌入式以太网端口或串行端口与编程器和HMI设备通信 热备用（HSB）冗余。需要一个冗余CPU和一个冗余内存Xchange模块（IC698RMX016），配置为每个单元中的冗余链路。 包含64 MB电池支持的用户内存和64 MB非易失性闪存，用于存储用户数据（程序、配置、寄存器数据和符号变量存储）。 通过引用表%W访问大容量内存。 可配置数据和程序存储器。 用梯形图、C、结构化文本和功能框图编程。 自动定位的符号变量，可以使用任意数量的用户内存。 支持90-70系列离散和模拟I/O、通信和其他模块。有关支持的模块列表，请参阅PACSystems RX7i安装手册GFK-2223。 支持Series 90-70支持的所有VME模块。 允许通过web进行数据监控。总共允许16个web服务器和FTP连接。 最多支持512个程序块。块的最大大小为128KB。 字中位引用。 电池供电的日历时钟。 CPU和模块固件通过CPU的RS-232或RS-485串行端口升级。 三个独立的串行端口：一个RS-485串行端口、一个RS-232串行端口和一个RS232以太网站管理器串行端口
嵌入式以太网接口提供：
使用以太网全球数据（EGD）进行数据交换 使用SRTP的TCP/IP通信服务 支持SRTP通道、Modbus/TCP服务器和Modbus/TPC客户端 完整的编程和配置服务 综合站点管理和诊断工具 两个全双工10BaseT/100BaseT/TX（RJ-45连接器）端口，带有内部网络交换机，提供自动协商的网络速度、双工模式和交叉检测。 与以太网上的SNTP时间服务器进行时间同步（与5.00版或更高版本的CPU模块一起使用时）。 用户可配置冗余IP允许： 从HSB冗余对中的活动和非活动以太网接口生成的EGD交换机的配置。 在HSB冗余CPU中，EGD交换的产生来自未配置冗余IP地址的以太网接口。
Configurable data and program memory
The RX7i CPU is programmed and configured by programming software to control the machine, process and material handling system in real time. The CPU uses the VME64 standard format to communicate with the I/O and intelligent option modules through a rack mounted backplane. It communicates with programmer and HMI device through embedded Ethernet port or serial port Hot Standby (HSB) redundancy. A redundant CPU and a redundant memory Xchange module (IC698RMX016) are required, which are configured as redundant links in each unit. Contains 64 MB of battery backed user memory and 64 MB of non-volatile flash memory for storing user data (programs, configurations, register data, and symbol variable storage). Access bulk memory by referencing table% W. Configurable data and program memory. Programming with ladder diagram, C, structured text and functional block diagram. Any amount of user memory can be used for automatically located symbolic variables. Supports 90-70 series discrete and analog I/O, communications, and other modules. For a list of supported modules, see the PACSystems RX7i Installation Manual GFK-2223. Supports all VME modules supported by the Series 90-70. Allow data monitoring through the web. A total of 16 web servers and FTP connections are allowed. A maximum of 512 blocks are supported. The maximum size of a block is 128KB. Word median reference. Battery powered calendar clock. The CPU and module firmware are upgraded through the CPU's RS-232 or RS-485 serial port. Three independent serial ports: one RS-485 serial port, one RS-232 serial port and one RS232 Ethernet website manager serial port
Embedded Ethernet interface provides:
Data exchange using Ethernet global data (EGD) TCP/IP communication services using SRTP Support SRTP channels, Modbus/TCP servers and Modbus/TPC clients Complete programming and configuration services Integrated site management and diagnostic tools Two full duplex 10BaseT/100BaseT/TX (RJ-45 connector) ports with internal network switches to provide automatically negotiated network speeds Duplex mode and cross detection. Time synchronization with SNTP time server over Ethernet (when used with CPU module version 5.00 or higher). User configurable redundant IP allows: configuration of EGD switches generated from active and inactive Ethernet interfaces in HSB redundant pairs. In HSB redundant CPU, EGD exchange is generated from Ethernet interface without redundant IP address.
