6009BZ10000 DCS控制器模块
功能特性兼容性：
规格兼容双高形状因子I/O连接器类型：64针DIN 41612 I/O组织：16个I/O端口，8位宽。可寻址到短监督或短非特权I/O映射内的任何地址。提供了单独的端口方向控制跳线。寻址方案：16个端口可在8位或16位边界上单独寻址。12个DIP开关提供无限短数据I/O地址映射选择。数据传输总线：A16:D16加电初始化：所有输出通过主清除在三态模式下初始化。任何到最终端口的写入传输都会自动释放三态模式。I/O电路：TTL兼容接收器-24 mA源-6.5 mA数据极性：高真值或低真值安装：除A1物理/环境温度范围外的任何插槽：0至55°C，工作温度-20至85°C，存储相对湿度范围：20至80%，非冷凝冷却：对流功率要求：+5 V，最大3 A商标标志是的注册商标。其他注册商标是其各自所有者的财产。
数据采集
应用•工厂自动化和仪表•过程控制和监控•实验室仪表•机器监控•数据采集和控制简介-本产品设计用于支持64通道差分或单端宽范围（±25 mV至±10 V）模拟输入。该板支持以下操作模式，如下所述：自动扫描单通道随机轮询定时脉冲串本地触发脉冲串远程触发脉冲串增益加载124个双端口数据寄存器为所有通道的连续扫描提供存储。扫描模式在通电、系统复位或在程序控制下自动执行。双端口寄存器允许VMEbus随时访问以读取最新存储的数据。通道增益可以跳线选择为x1、x10或x100，也可以为每个通道单独编程。扫描速率可编程至58 kCPS（千信道/秒）。低通输入滤波器可用。功能框图，订购选项见本规范（保留供将来使用的选项）C=输入选项0=64个Diff/SE模拟输入通道1=64个SE模拟输入，具有改进的高频抑制连接器数据类型推荐连接组件P3和P4 I/O连接器64针IDC匹配连接器（64针）应力消除（用于64针连接器）Panduit 120-964-435E Panduit 100-000-032 96针离散线匹配连接器（96针离散）母压接触点（96针离散型）AMP 925486-1 AMP 530151-6**连接器外壳（用于96针连接器）Harting 09 03 096 0501 96针IDC匹配连接器（96针质量端接）ERNI 913.031 0.033英寸带状电缆（96针批量端接）ERNI 913.0 49应变消除插件（0.033英寸条形电缆）Harding 09 02 000 9912连接器外壳（适用于96针连接器PC板I/O连接器零件号Panduit 101-096-033A注*-当VMIC信号调节产品与VMIVME-3128耦合时，**AMP压接工具零件号90301-2。
Feature compatibility:
Specifications compatible dual high shape factor I/O connector type: 64 pin DIN 41612 I/O organization: 16 I/O ports, 8-bit wide. Addressable to any address within a short supervised or short non privileged I/O map. A separate port direction control jumper is provided. Addressing scheme: 16 ports can be individually addressed on 8-bit or 16 bit boundaries. The 12 DIP switches provide unlimited short data I/O address mapping options. Data transmission bus: A16: D16 power on initialization: all outputs are initialized in the tri state mode through the main clearing. Any write transmission to the final port will automatically release the tri state mode. I/O circuit: TTL compatible receiver - 24 mA source - 6.5 mA data polarity: high true value or low true value installation: any slot except A1 physical/environmental temperature range: 0 to 55 ° C, operating temperature - 20 to 85 ° C, storage relative humidity range: 20 to 80%, non condensing cooling: convection power requirement:+5 V, maximum 3 A trademark is a registered trademark of. Other registered trademarks are the property of their respective owners.
Data acquisition
Application • Factory Automation and Instrumentation • Process Control and Monitoring • Laboratory Instrumentation • Machine Monitoring • Data Acquisition and Control Introduction - This product is designed to support 64 channel differential or single ended wide range (± 25 mV to ± 10 V) analog inputs. The board supports the following operation modes, as described below: automatic scanning single channel random polling timing pulse train local trigger pulse train remote trigger pulse train gain loading 124 dual port data registers to provide storage for continuous scanning of all channels. The scanning mode is automatically executed under power on, system reset or program control. The dual port register allows VMEbus to access at any time to read the latest stored data. The channel gain can be selected as x1, x10, or x100 by jumpers, or can be individually programmed for each channel. The scan rate can be programmed to 58 kCPS (thousands of channels per second). Low pass input filters are available. Functional block diagram, see this specification for ordering options (options reserved for future use) C=input options 0=64 Diff/SE analog input channels 1=64 SE analog inputs, With improved high-frequency suppression connector data type Recommended connection components P3 and P4 I/O connector 64 pin IDC matching connector (64 pin) Stress relief (for 64 pin connector) Panduit 120-964-435E Panduit 100-000-032 96 pin discrete line matching connector (96 pin discrete) Female crimp contact (96 pin discrete) AMP 925486-1 AMP 530151-6 * * Connector housing (for 96 pin connector) Harting 09 03 096 0501 96 pin IDC matching connector (96 pin quality termination) ERNI 913.031 0.033 inch ribbon cable (96 pin batch termination) ERNI 913.0 49 strain relief plug-in (0.033 inch ribbon cable) Harding 09 02 000 9912 connector housing (applicable to 96 pin connector PC board I/O connector part number Panduit 101-096-033A Note * - When VMIC signal conditioning product is coupled with VMIVME-3128, * * AMP crimping tool part number 90,301-2.
