5735088-36 DSIM2918 机器人卡件
功能特性符合性：
本产品符合VMEbus规范（ANSI/IEEE STD 1014-1987 IEC 821和297），具有以下助记符：A24:A16:D32/D16/D08（EO）：从：39/3D:29/2D:6U形状因数输出连接器类型：此板使用两个96针母连接器。对于大规模终端（IDC），建议使用ERNI IDC DIN连接器和0.033英寸30 AWG带状电缆。ERNI订单号为：96针连接器913 031 96导线0.033英寸电缆913 049对于离散导线使用，建议使用Harting连接器。该连接器由带有阴压接触点的触点外壳组成。Harting订单号为：96针连接器09 03 096 3214母接头压接触点09 02 000 8484压接工具（用于剥线）09 99 000 0075分立导线连接器需要一个带有固定杆的外壳。我们推荐哈廷住宅。其订单号为09 03 096 0501。该外壳可将离散电缆锁定到板连接器上，并提供应变消除。I/O组织：16个输出端口，8位宽，共128个输入，可寻址到短监督和/或短非特权或标准监督和/标准非特权I/O映射中的任何地址。寻址方案：32个字节可在8、16或32位边界上单独寻址。板ID寄存器位于板的基地址。控制和状态寄存器（CSR）堆叠在订购选项 针离散线匹配连接器（96针离散）Harting 09 03 096 3214母压接触点（96针分立）Harting09 02 000 8484连接器外壳（用于96针连接器）Harting0903 096 0501两个PC板连接器零件号ERNI 913 216*Harting压接工具零件号为09 99 000 0075。 建议新应用使用A1C选项。有关订购信息 规范如有更改，恕不另行通知。ID寄存器。十六个输入字节位于CSR上方。20个跳线建立了电路板的基本地址。另一个跳线用于标准或短I/O访问。
该设备符合FCC规则规定
操作必须符合以下两个条件：
（1）本设备可能不会造成有害干扰，以及（2）本设备必须接受接收到的任何干扰，包括可能导致不期望操作的干扰。FCC B类注：根据FCC规则第15部分，本设备经过测试，符合B类数字设备的限制。当设备在商业环境中运行时，这些限制旨在提供合理的保护，防止有害干扰。本设备产生、使用和辐射射频能量，如果未按照说明手册安装和使用，可能会对无线电通信造成有害干扰。在住宅区操作该设备可能会造成有害干扰，在这种情况下，用户需要自费纠正干扰。注意：未经负责合规的一方明确批准的更改或修改可能会使用户无权操作设备。加拿大法规 B类数字设备符合加拿大ICES-003。注：任何测试和发现符合FCC无意散热器或EN55022（以前为CISPR 22）的设备均符合ICES-002。
Conformity of functional characteristics:
This product complies with VMEbus specification (ANSI/IEEE STD 1014-1987 IEC 821 and 297), and has the following mnemonics: A24: A16: D32/D16/D08 (EO): Slave: 39/3D: 29/2D: 6U shape factor output connector type: this board uses two 96 pin female connectors. For large scale terminals (IDC), it is recommended to use ERNI IDC DIN connectors and 0.033 inch 30 AWG ribbon cables. ERNI Order No.: 96 pin connector 913 031 96 wire 0.033 inch cable 913 049 Harting connector is recommended for discrete wire use. The connector consists of a contact housing with a female contact point. Harting Order No.: 96 pin connector 09 03 096 3214 female connector crimping contact point 09 02 000 8484 crimping tool (for stripping) 09 99 000 0075 Discrete wire connector requires a housing with a fixing rod. We recommend Harting House. Its order number is 09 03 096 0501. The housing locks discrete cables to the board connector and provides strain relief. I/O organization: 16 output ports, 8-bit wide, 128 inputs in total, can address to any address in short supervised and/or short non privileged or standard supervised and/or standard non privileged I/O mapping. Addressing scheme: 32 bytes can be individually addressed on 8, 16 or 32-bit boundaries. The board ID register is located at the base address of the board. The control and status registers (CSR) are stacked on the ordering option pin discrete wire matching connector (96 pin discrete) Harting 09 03 096 3214 female pressure contact point (96 pin discrete) Harting 09 02 000 8484 connector housing (for 96 pin connector) Harting 0903 096 0501 The part number of the two PC board connectors ERNI 913 216 * The part number of the Harting crimping tool is 09 99 000 0075. The A1C option is recommended for new applications. The ordering information specifications are subject to change without notice. ID register. Sixteen input bytes are above the CSR. 20 jumpers establish the basic address of the circuit board. The other jumper is for standard or short I/O access.
The equipment complies with FCC rules
Operation must meet the following two conditions:
(1) the equipment may not cause harmful interference, and (2) the equipment must accept any interference received, including interference that may cause unexpected operation. FCC Class B Note: According to Part 15 of FCC Rules, this equipment has been tested and meets the limits of Class B digital equipment. These limits are intended to provide reasonable protection against harmful interference when the equipment is operating in a commercial environment. This equipment generates, uses and radiates radio frequency energy. If it is not installed and used according to the instruction manual, it may cause harmful interference to radio communication. Operating the equipment in residential areas may cause harmful interference, in which case the user needs to correct the interference at his own expense. Note: Changes or modifications not expressly approved by the party responsible for compliance may result in users having no right to operate the equipment. Canadian regulation Class B digital equipment complies with Canadian ICES-003. Note: Any equipment tested and found to comply with FCC unintentional radiator or EN55022 (formerly CISPR 22) shall comply with ICES-002.
