DSTK150 自动化备件
硬件配置
启用I/O的配置存储后的EGD消费者交换存储包含消耗的EGD交换的硬件配置，该硬件配置还将CPU配置为启用I/O的停止模式，现在将导致PLC开始消耗EGD交换。以前，如果CPU以前处于停止I/O禁用模式，则会产生交换，但不会消耗。当PLC处于停止模式输入/输出启用状态时，停止模式I/O启用状态下的EGD生成现在生成EGD交换。新的CPU功能和增强硬件发布–RX7i CPU的Cx提供ATEX机构批准。CPU限制和开放问题主题描述加载或存储包含大量块或符号的逻辑导致断开如果用户试图将包含大量块（>120）和/或大量符号的逻辑加载或存储到PLC或从PLC加载或存储逻辑，CPU将断开连接，直到连接超时才与编程器重新连接。在某些情况下，用户需要在断开电池的情况下重新打开电源。尽管这是一个PLC问题，但只有在使用CIMPLICITY机器版4.00 SP4 Special 1或更高版本时才能看到这种行为。逐字更改期间的以太网断开如果在逐字更改过程中以太网连接断开，程序员可能不会在重新连接后允许后续逐字更改，因为它认为当前连接了另一个程序员。如果发生这种情况，您应该脱机，然后重新联机。
hardware configuration
The EGD consumer exchange storage after I/O configuration storage is enabled includes the hardware configuration of consumed EGD exchange. The hardware configuration also configures the CPU to enable I/O stop mode, which will now cause the PLC to start consuming EGD exchange. Previously, if the CPU was previously in Stop I/O Disable mode, a swap would occur, but it would not be consumed. When the PLC is in the stop mode I/O enable state, EGD generation in the stop mode I/O enable state now generates an EGD exchange. New CPU Features and Enhanced Hardware Releases – The RX7i CPU's Cx is available for ATEX agency approval. The topic of CPU limitation and open issues describes that loading or storing logic containing a large number of blocks or symbols causes disconnection. If the user tries to load or store logic containing a large number of blocks (>120) and/or symbols to or from the PLC, the CPU will disconnect and will not reconnect with the programmer until the connection timeout. In some cases, the user needs to turn on the power again when the battery is disconnected. Although this is a PLC problem, you can only see this behavior when using CIMPLICITY machine version 4.00 SP4 Special 1 or later. Ethernet disconnection during verbatim change If the Ethernet connection is disconnected during verbatim change, the programmer may not allow subsequent verbatim change after reconnection, because it considers that another programmer is currently connected. If this happens, you should go offline and then go back online.
大型运行模式存储
逐字更改或在线编辑会话期间的电源循环问题如果在运行模式存储期间出现电源循环，逐字更改或者大型程序的在线编辑更改，CPU可能会在内存损坏的情况下通电。要从这种情况中恢复，用户需要清除CPU故障并再次存储。带消息模式的Modbus站地址配置当端口在运行模式下配置为消息模式时，它将在停止模式下自动切换到Modbus协议。然而，目前无法在此模式下配置Modbus站点地址。默认地址为1。重要产品信息9 GFK-2244E主题描述取消下载导致断开如果在某些文件已存储但尚未存储程序文件的时间之间取消了从编程器的下载，PLC将断开连接而不重新连接。用户可以重启PLC以重新连接。作为VME主机运行的第三方模块作为VME主设备运行的第二方模块尚未通过RX7i进行测试。有兴趣集成此类功能的用户应联系技术支持。GBC可能会默认其输出比预期晚250毫秒。对于此版本的RX7i CPU，Genius总线控制器用于检测CPU故障的计时器增加了250毫秒。结果公式为：（2 x CPU配置的看门狗定时器）+250 ms，最大值为3秒。此GBC计时器的最大设置上限为3秒。因此，在某些RX7i CPU故障的情况下，与90-70 CPU的相同情况相比，GBC可能会在250毫秒后默认其输出。
Large operating mode storage
Power cycle problems during verbatim changes or online editing sessions If power cycles, verbatim changes, or online editing changes of large programs occur during run mode storage, the CPU may power up when memory is damaged. To recover from this situation, the user needs to clear the CPU fault and store it again. Modbus station address configuration with message mode When the port is configured as message mode in operation mode, it will automatically switch to Modbus protocol in stop mode. However, it is currently not possible to configure the Modbus site address in this mode. The default address is 1. Important Product Information 9 GFK-2244E Topic Description Cancelling the download causes disconnection If the download from the programmer is cancelled between the time when some files have been stored but the program files have not been stored, the PLC will disconnect without reconnecting. The user can restart the PLC to reconnect. The third party module running as the VME host and the second party module running as the VME master have not passed the RX7i test. Users interested in integrating these functions should contact Technical Support. GBC may default to output 250 milliseconds later than expected. For this version of the RX7i CPU, the Genius Bus Controller timer used to detect CPU failures has been increased by 250 milliseconds. The result formula is: (2 x watchdog timer configured by CPU)+250 ms, the maximum value is 3 seconds. The maximum setting limit of this GBC timer is 3 seconds. Therefore, in the case of some RX7i CPU failures, GBC may default its output after 250 milliseconds compared with the same situation of 90-70 CPUs.
