DSTK181工控模块控制器
非关键CPU软件事件
密码级别2的强制当密码设置为级别2时，用户不再允许切换强制。从中断块调用DoIO功能块使用DoIO功能模块在中断块中扫描其输入或输出的模块现在可以包括在正常IO扫描中。BUS_RD/WR BYTE功能块使用SINGLE_WORD访问类型调用当VME内存区域接口类型设置为SINGLE_ WORD且逻辑执行字节大小的读或写（BUS RD BYTE长度1，BUS WRT BYTE长1）时，CPU现在正确执行字节大小读或写。在包含GBC的扩展机架的电源循环期间生成的故障在包含GBB的扩展机架电源循环期间，将不再生成指示“非关键CPU软件事件”的信息性故障，错误代码为269。这些故障是有害故障。电池和闪存加电模式以前，如果CPU配置为从闪存加载配置和逻辑，并在启用I/O的运行模式下重新通电，则CPU将在禁用I/O的运行状态下加电。在1.50版中，如果没有电池，CPU将在运行模式下通电，I/O被禁用。如果有电池，CPU将在启用I/O的运行模式下通电。%S1-%S8上的转换位现在可以正常工作了。以前，这些状态位的转换位在多次扫描时保持打开。通过ETM加载逻辑当编程器通过ETM模块连接到PLC时，包含大于8K的块的逻辑负载将不再导致编程器断开连接，CPU将在ETM模块上记录模块丢失故障。Modbus RTU协议大型字参考地址的写入和读取大于16385的字参考表地址的写入与读取现在已正确完成。
Non critical CPU software events
Password Level 2 Enforcement When the password is set to Level 2, the user is no longer allowed to switch enforcement. The module that calls the DoIO function block from the interrupt block and uses the DoIO function module to scan its inputs or outputs in the interrupt block can now be included in the normal IO scan. BUS_ The RD/WR BYTE function block uses SINGLE_ WORD access type call when VME memory area interface type is set to SINGLE_ When WORD and the logic executes byte size read or write (BUS RD BYTE length is 1, BUS WRT BYTE length is 1), the CPU now correctly executes byte size read or write. Faults generated during the power cycle of the expansion rack containing GBC During the power cycle of the expansion rack containing GBB, informational faults indicating "non critical CPU software events" will no longer be generated, with error code 269. These faults are harmful. Prior to battery and flash power up modes, if the CPU was configured to load configuration and logic from flash and power up again in the I/O enabled operating mode, the CPU would power up in the I/O disabled operating state. In version 1.50, if there is no battery, the CPU will be powered up in running mode and I/O will be disabled. If there is a battery, the CPU will power up in the I/O enabled operating mode.% The conversion bit on S1 -% S8 can now work normally. Previously, the transition bits of these status bits remained open during multiple scans. Loading logic through ETM When the programmer is connected to the PLC through ETM module, the logic load containing blocks larger than 8K will no longer cause the programmer to disconnect, and the CPU will record the module loss fault on the ETM module. The writing and reading of large word reference address of Modbus RTU protocol, which is greater than 16385, has been completed correctly.
解决的以太网问题主题
描述Station Manager参数无需大写输入对于CHSOSW命令，pl_parity、pl_flow_control、，和time_sync参数值不再需要大写并用双引号（“”）括起来。参考表网页显示问题参考表网页上位内存中字节或单词值的显示已更正。当值为负值时，位内存中有符号十进制值的显示现在是正确的。例如：从%M1开始的单词0x817A（%M16到%M1）正确显示为无符号格式的33146和有符号格式的-32390。参考表网页显示限制参考表网页在几种情况下不再错误地限制最大可查看地址。固件升级期间按以太网重启在固件升级期间按下以太网重启按钮将正确导致固件升级失败。升级过程需要重新启动。Web服务器浏览器限制在装有Windows 95 O.S.的PC上使用Netscape 4.0版时，参考表网页现在将正确显示。IO故障表网页显示问题IO故障表页面将显示每个故障以及上次正确清除的时间。Web服务器和FTP服务器连接配置验证程序员现在将强制执行Web服务器和FTP连接总数不超过16的限制。
Ethernet problem solved topic
Description Station Manager parameters do not need to be input in uppercase For the CHSOSW command, pl_ parity、pl_ flow_ Control,, and time_ The sync parameter value no longer needs to be capitalized and enclosed in double quotation marks (""). The display of bytes or word values in the upper memory of the reference table page has been corrected. When the value is negative, the display of the signed decimal value in bit memory is now correct. For example, words 0x817A (% M16 to% M1) starting from% M1 are correctly displayed as 33146 in unsigned format and - 32390 in signed format. The display limit of the reference table page The reference table page will no longer incorrectly limit the maximum viewable address in several cases. Pressing the Ethernet restart button during the firmware upgrade will correctly cause the firmware upgrade to fail. The upgrade process requires a restart. When the Web server browser is restricted to using Netscape version 4.0 on a PC with Windows 95 O.S., the reference table page will now display correctly. The IO fault table page displays the problem. The IO fault table page displays each fault and the last correct clearing time. The Web server and FTP server connection configuration verification programmer will now enforce that the total number of Web server and FTP connections does not exceed the limit of 16.
