DSRC113 数控模块
安装数字输入模块
在安装或操作IMDSI1数字输入模块之前，1.安装模块前，请阅读操作程序部分。2.执行安装部分中的步骤。3.如果出现问题，请参阅故障排除部分以解决问题。4.有关定期维护要求，请参阅维护部分。简介文件惯例1-4 WBPEEUI240752A0 。请参阅维修和更换程序以更换模块。6.使用支持服务部分了解有关订购备用模块和保修信息的信息。 描述和操作使用框图和示意图来解释模块操作和输入电路。安装包括安装模块和准备操作的初步步骤。它包括双列直插式开关和跳线设置、安装、接线连接、布线和操作前检查。操作程序提供有关前面板指示灯和启动程序的信息。故障排除解释错误指示的含义并包含故障排除步骤。维护包含计划的维护任务和程序。维修和更换程序包含说明如何更换模块的程序。支持服务解释Elsag Bailey向客户提供的服务和培训。
磁场和电磁场射频共模
0.15 MHz至80 MHz（ENV 50141）未调制均方根：10 V/m调幅：80%AM（1 kHz）源阻抗：150Ω 发射测试射频辐射场，30 MHz至1000 MHz（ENV 55011）A级CE标志声明EMC 89/336/EEC低压指令73/23/EEC本产品安装在INFI 90 OPEN机柜中时，符合CE标志要求的以下指令/标准：EN50081-2通用排放标准-第2部分：工业环境EN50082-2通用抗扰度标准-第二部分：工业环保EN 61010测量用电气设备的安全要求，控制和实验室使用-第1部分：一般要求认证CSA（加拿大标准协会）FM（工厂互助会）（待定）根据CSA C22.2第1010.1-92号批准，认证用于普通（非危险）场所的过程控制设备。非易燃：I类2类A、B、C、D组II类2类F、G组规范如有更改，恕不另行通知。
Installing the Digital Input Module
Before installing or operating the IMDSI1 digital input module, 1. Before installing the module, please read the operating procedures section. 2. Perform the steps in the Installation section. 3. If there is a problem, please refer to the troubleshooting section to solve the problem. 4. Refer to the maintenance section for regular maintenance requirements. Introduction Document Practice 1-4 WBPEEUI240752A0. Refer to the service and replacement procedure to replace the module. 6. Use the Support Services section for information on ordering spare modules and warranty information. Description and operation Use block diagrams and schematics to explain module operation and input circuits. Installation includes the initial steps of installing the module and preparing for operation. It includes setting, installation, wiring connection, wiring and pre operation inspection of dual in-line switch and jumper. The operator program provides information about the front panel indicators and the startup program. Troubleshooting explains the meaning of error indications and includes troubleshooting steps. Maintenance includes planned maintenance tasks and procedures. The repair and replacement procedure contains a procedure that describes how to replace a module. Support services explain the services and training Elsag Bailey provides to customers.
Magnetic field and electromagnetic field RF common mode
0.15 MHz to 80 MHz (ENV 50141) unmodulated root mean square: 10 V/m Amplitude modulation: 80% AM (1 kHz) Source impedance: 150 Ω RF radiation field for emission test, 30 MHz to 1000 MHz (ENV 55011) Class A CE marking statement EMC 89/336/EEC low-voltage directive 73/23/EEC When this product is installed in INFI 90 OPEN cabinet, The following directives/standards meet the requirements of the CE mark: EN50081-2 General Emission Standard - Part 2: Industrial Environment EN50082-2 General Immunity Standard - Part 2: Industrial Environment EN 61010 Safety Requirements, Control and Laboratory Use of Electrical Equipment for Measurement - Part 1: General Requirements Certification CSA (Canadian Standards Association) FM (Factory Mutual) (to be determined) Approved according to CSA C22.2 No. 1010.1-92, Process control equipment certified for use in general (non hazardous) locations. Nonincendive: Class I, Division 2, Groups A, B, C and D, Class II, Division 2, Groups F and G specifications are subject to change without notice.
