57160001-NF
触摸屏和覆盖层
金属外壳框架和外壳材料为粉末涂层铝。该粉末涂料可耐受以下化学品的暴露而无明显变化：粉末涂料在室温下对以下化学品的耐受性有限：乙酸10%磷酸4%柠檬酸10%磷酸10%柴油海水蒸馏水氯化钠2%食用油氯化钠20%燃油硫酸20%过氧化氢3%自来水丁醇硝酸3%盐酸5%硝酸10%异丙醇磷酸43%次氯酸钠10%松节油如果需要接触上述任何化学品，建议首先在金属外壳的“不可见”位置测试该化学品。触摸屏和覆盖层第5节耐化学性32 3BSE043449R501粉末涂料在室温下对以下化学品几乎没有或没有抵抗力：触摸屏和重叠Autotex F157/F207 Autotex F1 57或F207覆盖触摸屏周围的覆盖层。根据DIN 42 115第2部分，耐溶剂Autotex F157/F207 F250可承受以下化学品的暴露时间超过24小时，且无明显变化：乙酸，conc。甲基乙基酮甲苯丙酮硝酸30%三氯乙烯氨5%苯酚二甲苯氨，浓度。
氢氧化钠5%97辛烷值无铅汽油乙酸乙酯氢氧化钠30%98辛烷值含铅汽油乙腈柴油Downey/Lenor1磷酸（<30%）Ajax/Vim溶液乙醇铁氰化钾碱碳酸盐溶液1甘油钾氢氧化钠（<30%%）氨（<40%）1乙二醇纯松节油醋酸（<50%）Gumption 1 SBP 60/951 Ariel粉末溶液1盐酸酸（<36%）硫酸（<10%）漂白1亚麻籽油番茄酱蓖麻油甲醇三氯乙酸（<50%）苛性钠（<40%）1硝酸（<10%%）White Spirit Section 5耐化学性触摸屏表面3BSE043449R501 33 Autotex可承受DIN 42 115 Part 2暴露于冰醋酸长达1小时，无明显变化。Autotex不耐100°C以上的高压蒸汽或以下化学品：户外使用与所有聚酯基薄膜一样，Autotex F157/F207F250不适合在长期暴露于阳光直射的条件下使用。触摸屏表面面板上的触摸屏表面能够承受暴露于以下溶剂而无明显变化：Autoflex EB建议使用可从供应商处订购的Autoflex EB触摸显示屏保护膜。切削油石蜡油Windex1环己醇Persil粉末在溶液中1 Wisk二丙酮醇石油精1-1纹理有极微弱的光泽。浓矿物酸苯甲醇浓苛性碱溶液氯甲烷
Touch screen and overlay
The metal shell frame and shell material are powder coated aluminum. The powder coating can withstand the exposure of the following chemicals without obvious changes: the powder coating has limited resistance to the following chemicals at room temperature: acetic acid 10% phosphoric acid 4% citric acid 10% phosphoric acid 10% diesel oil seawater distilled water sodium chloride 2% edible oil sodium chloride 20% fuel oil sulfuric acid 20% hydrogen peroxide 3% water butanol nitric acid 3% hydrochloric acid 5% nitric acid 10% isopropanol phosphate 43% sodium hypochlorite 10% turpentine If you need to contact any of the above chemicals, It is recommended that the chemical be tested first in the "invisible" position of the metal enclosure. Section 5 Chemical resistance of touch screen and coating 32 3BSE043449R501 powder coating has little or no resistance to the following chemicals at room temperature: touch screen and overlapping Autotex F157/F207 Autotex F1 57 or F207 cover the coating around the touch screen. According to DIN 42 115 Part 2, solvent resistant Autotex F157/F207 F250 can withstand exposure to the following chemicals for more than 24 hours without significant changes: acetic acid, conc. Methyl ethyl ketone toluene acetone nitric acid 30% trichloroethylene ammonia 5% phenol xylene ammonia, concentration.
Sodium hydroxide 5% 97 octane number unleaded gasoline ethyl acetate sodium hydroxide 30% 98 octane number leaded gasoline acetonitrile diesel oil phosphoric acid (<30%) Ajax/Vim solution ethanol potassium ferricyanide alkali carbonate solution 1 potassium glycerine sodium hydroxide (<30%%) ammonia (<40%) 1 ethylene glycol pure turpentine acetic acid (<50%) Gumption 1 SBP 60/951 Ariel powder solution 1 hydrochloric acid (<36%) sulfuric acid (<10%) Bleaching 1 flaxseed oil tomato sauce castor oil methanol trichloroacetic acid (<50%) caustic soda (<40%) 1 nitric acid (<10%%) White Spirit Section 5 chemical resistant touch screen surface 3BSE043449R501 33 Autotex can withstand exposure of DIN 42 115 Part 2 to glacial acetic acid for 1 hour without obvious change. Autotex is not resistant to high pressure steam above 100 ° C or the following chemicals: Like all polyester based films, Autotex F157/F207F250 is not suitable for long-term exposure to direct sunlight. The touch screen surface on the touch screen surface panel can withstand exposure to the following solvents without significant changes: Autoflex EB recommends using an Autoflex EB touch screen protective film that can be ordered from the supplier. Cutting oil paraffinic oil Windex1 cyclohexanol Persil powder has very weak luster in the texture of 1 Wisk diacetone alcohol petroleum essence 1-1 in solution. Concentrated mineral acid, benzyl alcohol, concentrated caustic solution, methyl chloride
