KONGSBERG RCU510船舶控制卡件
传感器信号监测SIGNAL（信号）按钮的操作允许监控所选通道传感器信号值。显示的参数取决于安装在所选通道卡上的传感器驱动模块的类型。要进入传感器信号监测操作，请执行以下操作：（1）按住所需通道卡RESET/SELECT（重置/选择）按钮约1.5秒，直到所选图标出现在通道显示器上。（2） 按下SIGNAL（信号）按钮，所选通道卡显示屏将指示传感器信号。显示的值将取决于安装在通道卡上的传感器驱动模块的类型，如下所示：a.催化传感器驱动模块显示屏将显示在01和02之间测得的带电电桥电压（单位：mV）。02是通道卡上惠斯通电桥后半部的中心点。b、 4-20mA传感器驱动模块显示屏将以mA为单位显示传感器回路电流。（3）按下（）或（）按钮或等待30秒退出信号模式。4.7查看时钟/日历操作时钟按钮将导致当前时间和日期显示在所选通道卡上。注意：此操作需要选择控制卡，但此操作对所选控制卡没有影响，该控制卡仅用作显示设备。
进入时钟/日历操作
如下操作：（1）按住所需的通道卡RESET/SELECT（重置/选择）按钮约1.5秒，直到所选图标出现在通道显示器上（2）按下CLOCK（时钟）按钮，所选通道卡显示器将指示当前时间。注：时钟采用24小时制。（3） 再次按下CLOCK（时钟）按钮，所选通道卡显示屏将显示当前日期、月份和年份。注：1.根据系统配置，日和月的显示格式可以是DD.MM或MM.DD。2.进一步按下CLOCK（时钟）按钮将在时间和日期之间切换显示。（4） 按下（）或（）按钮或等待30秒以退出时钟模式。4.8维护记录打印可以使用工程卡启动每个通道状态的详细打印输出或整个机架的汇总。数据以ASCII文本格式馈送至工程卡前面板上的工程串行端口。要输出每个通道卡的维护记录，请执行以下操作：（1）将RS232打印机插入工程卡串行端口。（2）按住所需通道卡RESET/SELECT（重置/选择）按钮约1.5秒，直到所选图标出现在通道显示器上。（3） 同时按下向上和向下按钮。输出以下数据时，所选通道卡将显示PRN
Sensor Signal Monitoring
The operation of the SIGNAL push-button allows the monitoring of the selected channels sensor signal value. The displayed parameter is dependent upon the type of sensor drive module fitted to the selected channel card. To enter the sensor signal monitoring operation, proceed as follows: (1) Push and hold the required channel card RESET/SELECT pushbutton for approximately 1.5 seconds until the selected icon appears on the channel display. (2) Push the SIGNAL push-button and the selected channel card display will indicate the sensor signal. The displayed value will depend on the type of sensor drive module fitted to the channel card as follows: a. Catalytic Sensor Drive Module The display will show the live bridge voltage measured between 01 and 02 in mV. 02 is the centre point of the second half of the Wheatstone bridge which is on the channel card. b. 4 - 20mA Sensor Drive Module The display will show the live sensor loop current in mA. (3) Push the ( ) or ( ) push buttons or wait 30 seconds to exit the SIGNAL mode. 4.7 View Clock/Calendar The operation of the CLOCK push-button will cause the present time and date to be displayed on a selected channel card. Note: This operation requires a control card to be selected but the operation has no effect on the selected control card, which is used as a display device only.
To enter the clock/calendar operation
proceed as follows: (1) Push and hold the required channel card RESET/SELECT pushbutton for approximately 1.5 seconds until the selected icon appears on the channel display (2) Push the CLOCK push-button and the selected channel card display will indicate the present time. Note: The clock uses the 24 hour format. (3) Push the CLOCK push-button a second time and the selected channel card display will indicate the present day, month and year. Notes: 1. The display format for day and month can read either DD.MM or MM.DD depending on the configuration of the system. 2. Further pushes of the CLOCK push-button will toggle the display between time and date. (4) Push the ( ) or ( ) push-buttons or wait 30 seconds to exit the CLOCK mode. 4.8 Maintenance Record Print Out A detailed printout of the status for each channel or a summary of the whole rack can be initiated using the Engineering Card. The data is fed in ASCII text format to the engineering serial port on the Engineering Card front panel. To output the maintenance record for each channel card, proceed as follows: (1) Plug a RS232 printer into the Engineering card serial port. (2) Push and hold the required channel card RESET/SELECT push button for approximately 1.5 seconds until the selected icon appears on the channel display. (3) Push the up ( ) and down ( ) buttons simultaneously. The selected channel card will display PRN while outputting the following data
产品优势
1：国外专业的供货渠道，具有价格优势
2：产品质量保证，让您售后无忧
3：全国快递包邮
4：一对一服务
公司主营范围简介
PLC可编程控制器模块，DCS卡件，ESD系统卡件，振动监测系统卡件，汽轮机控制系统模块，燃气发电机备件等，优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件、欧美进口模块。
产品广泛应用于冶金、石油天然气、玻璃制造业、铝业、石油化工、煤矿、造纸印刷、纺织印染、机械、电子制造、汽车制造、塑胶机械、电力、水利、水处理/环保、锅炉供暖、能源、输配电等等
