产品内容介绍
369-HI-0-0-0-0-H-E继电保护器
插入SD卡注：如下图所示（左侧示例），您可以设置写入控制选项卡以防止对SD卡执行写入操作。向上推卡舌，如右侧的示例所示，以释放锁并允许写入SD卡。在使用商用SD卡之前，请阅读制造商的说明。数据丢失处理SD卡时，请按照以下说明操作，以防止SD卡上的内部数据被破坏或发生SD卡故障： 避免将SD卡存放在有静电或电磁波的地方。 避免将SD卡存放在阳光直射、靠近加热器或其他可能发生高温的位置。 请勿弯曲SD卡。 请勿将SD卡跌落或撞击其他物体。 保持SD卡干燥。 请勿触摸SD卡接口。 请勿拆解或修改SD卡。 仅使用使用FAT或FAT32格式化的SD卡。HMIGTO无法识别NTFS格式的SD卡。使用FAT或FAT32格式化计算机上的SD卡
在从HMIGTO中卸下SD卡之前，请使用SD卡卸下过程停止对其进行的所有操作。如果不运行删除过程并强制提取SD卡，SD卡上的数据可能会损坏。 访问SD卡时，不要关闭或重置HMIGTO，也不要插入或取出SD卡。这样做可能会损坏SD卡或损坏其数据。 使用SD卡之前，请熟悉SD卡的正面和背面方向，以及SD卡连接器的位置。如果SD卡插入HMIGTO时未正确定位，则卡的内部数据和HMIGTO可能会损坏。
SD卡数据备份
要进行备份，您可以将SD卡直接插入计算机上的SD卡接口，或使用商用SD卡读卡器。如图所示，将领带穿过夹孔。接下来，转动领带并将其穿过头部，以便USB电缆可以穿过领带环的中心。现在，该剪辑已连接到USB电缆。 事先检查头部的方向。确保USB电缆穿过打结环的中心，并且打结可以穿过头部。 您可以用宽度为4.8 mm（0.19 in）、厚度为1.3 mm（0.05 in）的商用扎带代替提供的扎带。4按住夹子上的夹子，将步骤3中的电缆一直插入USB主机接口。确保将夹片固定在连接到HMIGTO的USB电缆上。设备损坏 清洁面板前，请关闭面板电源。 请勿使用坚硬或尖锐的物体操作触摸面板，否则可能会损坏面板表面。 请勿使用油漆稀释剂、有机溶剂或强酸化合物清洁装置。将新垫片连接到面板上。将垫片放在安装槽中，使垫片接缝位于面板底部。首先，按下图所示顺序将垫圈插入四个角。然后，将其余垫片插入安装槽中。注意： 面板挡板安装槽的中心是带肋的。确保完全插入垫圈，而不会卡住带肋部分。 使用工具插入垫片时，确保工具不会卡住橡胶垫片并导致撕裂。垫片的上表面应突出凹槽约2.0 mm（0.06 in.）。在将HMIGTO安装到面板中之前，检查垫圈是否正确插入。
Inserting the SD Card
NOTE: As shown in the image below (example on the left-hand side), you can set the Write-Control Tab to prevent write operations to the SD card. Push the tab up, as shown in the example on the right-hand side to release the lock and enable writing to the SD card. Before using a commercial-type SD card, read the manufacturer's instructions. LOSS OF DATA When handling the SD card, follow the instructions below to prevent internal data on the SD card from being destroyed or a SD card malfunction from occurring: Avoid storing the SD card where there is static electricity or electromagnetic waves. Avoid storing the SD card in direct sunlight, near a heater, or other locations where high temperatures can occur. Do not bend the SD card. Do not drop or strike the SD card against another object. Keep the SD card dry. Do not touch the SD card connectors. Do not disassemble or modify the SD card. Use only SD cards formatted using FAT or FAT32. The HMIGTO does not recognize NTFS formatted SD cards. Format the SD card on your computer using FAT or FAT32
Before removing the SD card from the HMIGTO, stop all operation on it using the SD card removal process. If you do not run the removal process and forcibly extract the SD card, data on the SD card may become corrupted. While a SD card is accessed, do not turn OFF or reset the HMIGTO, and do not insert or remove the SD card. Doing so could damage the SD card, or corrupt its data. Before using the SD card, familiarize yourself with the SD card's front and rear face orientation, as well as the position of the SD card connectors. If the SD card is not positioned correctly when inserted into the HMIGTO, the card's internal data and HMIGTO could become damaged.
SD Card Data Backup
To make your backups, you can either insert the SD Card directly into the SD Card interface on your computer, or use a commercially available SD Card reader As shown, pass the tie through the clip hole. Next, turn the tie and pass it through the head so that the USB cable can pass through the center of the tie loop. The clip is now attached to the USB cable. Check the direction of the head beforehand. Make sure that the USB cable is through the center of the tie loop and that the tie can pass through the head. You can substitute the tie provided with commercially available ties with a width of 4.8 mm (0.19 in) and thickness of 1.3 mm (0.05 in). 4 While pressing the grip on the clip, insert the cable from step 3 all the way into the USB host interface. Make sure that the clip tab is secured to the USB cable attached to the HMIGTO.EQUIPMENT DAMAGE Power off the panel before cleaning it. Do not use hard or pointed objects to operate the touch panel as you may damage the panel surface. Do not use paint thinner, organic solvents, or a strong acid compound to clean the unit.Attach the new gasket to the panel. Position the gasket in the installation groove so that the gasket seam is at the bottom of the panel. First, insert the gasket into the four corners, in the order shown in the image below. Then, insert the rest of the gasket into the installation groove. NOTE: The center of the panel bezel's installation groove is ribbed. Make sure that you insert the gasket all the way in without catching the ribbed sections. When using a tool to insert the gasket, make sure that the tool does not catch the rubber gasket and cause a tear.The upper surface of the gasket should protrude approximately 2.0 mm (0.06 in.) from the groove. Check the gasket is inserted correctly before installing the HMIGTO into a panel.
产品优势
1：国外专业的供货渠道，具有价格优势
2：产品质量保证，让您售后无忧
3：全国快递包邮
4：一对一服务
公司主营范围简介
PLC可编程控制器模块，DCS卡件，ESD系统卡件，振动监测系统卡件，汽轮机控制系统模块，燃气发电机备件等，优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件、欧美进口模块。
产品广泛应用于冶金、石油天然气、玻璃制造业、铝业、石油化工、煤矿、造纸印刷、纺织印染、机械、电子制造、汽车制造、塑胶机械、电力、水利、水处理/环保、锅炉供暖、能源、输配电等等
