产品内容介绍
1326AB-B430E-M2K4LS控制速度模块
结构规范安装在实心面板中的HMIGTO的正面已经使用与规范中所示标准等效的条件进行了测试。尽管HMIGTO的阻力水平与这些标准相当，但对HMIGTO没有影响的油可能会损害面板。这可能发生在存在汽化油的区域，或允许低粘度切削油长时间粘附在面板上的区域。如果面板正面保护板脱落，这些情况可能导致油进入面板，建议采取单独的保护措施。此外，如果存在未经批准的机油，它们可能会导致前面板塑料罩变形或腐蚀。因此，在安装面板之前，请确保确认面板操作环境中存在的条件类型。如果长期使用安装垫片，或者如果面板及其垫片从面板上拆下，则无法保持原有的防护等级。为了保持原有的保护水平，请确保定期更换安装垫片*2在面板中安装HMIGTO时，可能无法将HMIGTO与面板平齐安装。这是由于垫片的厚度造成的。HMIGTO和面板之间的液位差取决于垫片被压缩的程度。HMIGTO2315*3的电路板上有保形涂层。对于尺寸公差，所有+1/-0 mm（+0.04/-0 in）和R的角度均低于R3（R0.12 in）*4即使安装壁厚在“面板切割尺寸”的建议范围内，取决于墙的材料、尺寸和面板和其他设备的安装位置，安装壁也可能翘曲。为了防止翘曲，可能需要加强安装表面。
内存、时钟和触摸面板
简介注释： 当HMIGTO2300上显示指示电池电量低的消息时，向面板供电并给电池充满电。24小时内，电池充电至允许备用操作的水平。完成完全充电需要大约120小时（五天）。 锂电池的寿命为：电池环境温度为40°C（104°F）或以下时为10年，电池环境温度在50°C（122°F）及以下时为4.1年，电池的环境温度在60°C（140°F）以下时为1.5年。用于备份时： 电池充满电约100天。 使用半充电电池约6天。 当HMIGTO2310/2315上显示指示电池电量低的消息时，请更换电池（参见第134页）*1根据面板的工作温度和使用年限，时钟可能会从-380秒/月偏离至+90秒/月。对于这种精度水平不足的系统，用户应进行监控，并在需要时进行调整。有关如何连接控制器和其他类型设备的信息，请参阅屏幕编辑软件的相应设备驱动程序手册。使用SG端子将外部设备连接到面板时： 设置系统时，请确认没有创建短路回路。 当主机（PLC）单元未隔离时，将#5 SG终端连接到远程设备。将#5 SG端子连接至已知可靠的接地连接，以降低损坏电路的风险。串行端口未隔离。SG（信号接地）和FG（机架接地）端子连接在面板内。
Structural Specifications
The front face of the HMIGTO, installed in a solid panel, has been tested using conditions equivalent to the standards shown in the specification. Even though the HMIGTO's level of resistance is equivalent to these standards, oils that should have no effect on the HMIGTO can possibly harm the panel. This can occur in areas where either vaporized oils are present, or where low viscosity cutting oils are allowed to adhere to the panel for long periods of time. If the panel's front face protection sheet peels off, these conditions can lead to the ingress of oil into the panel and separate protection measures are suggested. Also, if non-approved oils are present, they may cause deformation or corrosion of the front panel’s plastic cover. Therefore, prior to installing the panel, be sure to confirm the type of conditions that will be present in the panel’s operating environment. If the installation gasket is used for a long period of time, or if the panel and its gasket are removed from the panel, the original level of protection cannot be kept. To maintain the original protection level, be sure to replace the installation gasket regularly. *2 When installing the HMIGTO in a panel, you may not be able to mount the HMIGTO flush with the panel. This occurs due to the thickness of the gasket. The difference in level between the HMIGTO and panel depends on how much the gasket is compressed. There is a conformal coating on circuit boards for HMIGTO2315 *3 For dimensional tolerance, everything +1/-0 mm (+0.04/-0 in) and R in angle are below R3 (R0.12 in). *4 Even if the installation wall thickness is within the recommended range for the “Panel Cut Dimensions”, depending on wall's material, size, and installation location of the panel and other devices, the installation wall could warp. To prevent warping, the installation surface may need to be strengthened.
Memory, Clock, and Touch Panel
Introduction NOTE: When the message indicating that the battery level is low is displayed, on the HMIGTO2300, supply power to the panel and fully charge the battery. In 24 hours the battery charges to a level that allows backup operation. Completing a full charge requires about 120 hours (five days). The lithium battery's lifetime is: 10 years when the battery's ambient temperature is 40 °C (104 °F) or less, 4.1 years when the battery's ambient temperature is 50 °C (122 °F) or less, and 1.5 years when the battery's ambient temperature is 60 °C (140 °F) or less. When used for backup: Approximately 100 days with a fully charged battery. Approximately 6 days with a half-charged battery. When the message indicating that the battery level is low is displayed on HMIGTO2310/2315, replace the battery (see page 134) *1 Depending on the operating temperature and age of panel, the clock can deviate from -380 to +90 sec/month. For systems where this level of precision is insufficient, the user should monitor and make adjustments when required.For information on how to connect controllers and other types of equipment, refer to the corresponding device driver manual of your screen editing software.When using the SG terminal to connect an external device to the panel: Verify that a short-circuit loop is not created when you set up the system. Connect the #5 SG terminal to remote equipment when the host (PLC) unit is not isolated. Connect the #5 SG terminal to a known reliable ground connection to reduce the risk of damaging the circuit.The serial port is not isolated. The SG (signal ground) and FG (frame ground) terminals are connected inside the panel.
公司主营产品图展示
产品优势
1：国外专业的供货渠道，具有价格优势
2：产品质量保证，让您售后无忧
3：全国快递包邮
4：一对一服务
公司主营范围简介
PLC可编程控制器模块，DCS卡件，ESD系统卡件，振动监测系统卡件，汽轮机控制系统模块，燃气发电机备件等，优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件、欧美进口模块。
产品广泛应用于冶金、石油天然气、玻璃制造业、铝业、石油化工、煤矿、造纸印刷、纺织印染、机械、电子制造、汽车制造、塑胶机械、电力、水利、水处理/环保、锅炉供暖、能源、输配电等等
