公司主营产品图展示
产品优势
1：国外专业的供货渠道，具有价格优势
2：产品质量保证，让您售后无忧
3：全国快递包邮
4：一对一服务
公司主营产品文字介绍
PLC可编程控制器模块，DCS卡件，ESD系统卡件，振动监测系统卡件，汽轮机控制系统模块，燃气发电机备件等，优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件、欧美进口模块。
产品广泛应用于冶金、石油天然气、玻璃制造业、铝业、石油化工、煤矿、造纸印刷、纺织印染、机械、电子制造、汽车制造、塑胶机械、电力、水利、水处理/环保、锅炉供暖、能源、输配电等等
产品详情内容介绍
AW641/52000910/STD二氧化硅分析仪
使用以下步骤标定模块。此中使用的输入包程序仅用作示例。建议预热5分钟校准前。可用输入包该模块最多可接受八个任意组合的输入包。共有六个类别
z电压，低带宽
z当前，低带宽
z电阻式温度检测器
z应变计
z电压，宽带宽
z线性热电偶
有关所需的输入范围、输出范围和零件，请参阅下表预期应用所需的数量。
注：5B型第三方包装使用第三方软件包时，请联系制造商寻求支持。
注：输入包作为修订级别A发布，由例如，零件号（AS–5B30001A）。更改将由更高级别的修订级别。
注：使用时，所有AS–5BXX输入包的可用输出范围为0-+5 V使用此模块。
低带宽（4 kHz）模拟电压输入包下表显示了可用低压的零件号和输入范围带宽模拟电压输入包。J890或J892模块可用于提供984之间的下降接口可编程控制器和S908远程I/O上800系列I/O的远程丢弃（RIO）网络。
两个接口模块都有两种型号
其中一种型号带有单个F连接器用于RIO电缆连接，一个带有两个F连接器。在里面此外，J892还包含两个支持ASCII输入/输出的半双工端口
远程放置的设备。DIP开关位置J890/J892接口设备都有一组DIP开关，位于模块背面。这些交换机用于设置唯一的RIO网络地址用于接口将驻留的远程放置。必须在上设置投递地址接口模块，然后将其安装在I/O外壳中，交换机设置为丢弃地址下降地址DIP开关有八个位置
注：如果RIO网络前端的控制器同时支持本地I/O删除和远程I/O，然后将删除地址#1保留给本地删除第一个远程drop地址为drop#2。如果控制器不支持本地I/O，第一个远程拖放地址为拖放#1。有关984的完整列表控制器及其I/O支持功能，请参阅远程I/O系统
规划和安装指南（890 USE 101 00）。用于丢弃寻址的开关位置。
Available Input Pack
Use the following procedure to calibrate the module. The input pack used in this procedure is used only as an example. A five-minute warm-up time is recommended prior to calibration.
The module accepts up to eight input packs of any mix. Six categories are available z Voltage, low bandwidth z Current, low bandwidth z RTD z Strain gauge z Voltage, wide bandwidth z Linear thermocouple Refer to the following tables for the desired input range, output range, and part number required for the intended application. NOTE: 5B type third party packs When using third party packs, contact the manufacturer for support. NOTE: Input packs are issued as revision level A’s, denoted by the last item of the part number, for example, (AS–5B30001A). Changes will be noted by higher revision levels. NOTE: The usable output range for all AS–5BXX input packs is 0—+5 V when used with this module. Low Bandwidth (4 kHz) Analog Voltage Input Packs The following table presents the part numbers and input ranges for the available low bandwidth analog voltage input packs.
A J890 or J892 module may be used to provide the drop interface between a 984 programmable controller and a remote drop of 800 series I/O on an S908 remote I/O (RIO) network. Both interface modules are available in two models - one with a single F connector for RIO cable connection and one with two F connectors. In addition, the J892 contains two half-duplex ports that will support ASCII input/output devices at the remote drop.
DIP Switch Location
This J890/J892 Interface devices both have a set of DIP switches located on the back of the module. These switches are used to set a unique RIO network address for the remote drop where the interface will reside. The drop address must be set on the Interface module before it is installed in the I/O housing Switch Settings for Drop Address The drop address DIP switch has eight positions NOTE: If the controller at the head end of the RIO network supports both a local I/O drop and remote I/O, then drop address # 1 is reserved for the local drop and the first remote drop is addressed as drop # 2. If the controller does not support local I/O, the first remote drop is addressed as drop # 1. For a complete list of 984 controllers and their I/O support capabilities, refer to the Remote I/O System Planning and Installation Guide (890 USE 101 00). Switch positions for drop addressing.
