公司主营产品图展示
产品优势
1：国外专业的供货渠道，具有价格优势
2：产品质量保证，让您售后无忧
3：全国快递包邮
4：一对一服务
产品详情介绍
3HAC028017-001伺服电机模块
探头和延长电缆上方
温度范围为-35°C至+260°C（-31°F至+500°F）前置器传感器在0之间°C至+45°C（+32°F至+113°F），
ISF保持在±18%以内7.87 V/mm（200 mV/mil）和DSL保持在±0.152 mm范围内（±6密耳）。
当在线性范围，相互作用两个独立传感器之间系统（串扰）将减少轴直径大于50 mV至少50毫米（2英寸）或更大。
你应该注意保持最小间距传感器尖端，通常至少轴向位置为40 mm（1.6 in）测量值或38毫米（1.5英寸）
用于径向振动测量将串扰限制在50 mV或以下。
径向振动或位置轴上的测量直径小于76.2 mm（3英寸）通常会改变比例系数。探头压力3300 XL 8 mm探针设计用于密封差速器探针尖端之间的压力和案例。探头密封材料由Viton®组成O型环。探针不是压力装运前测试。联系我们的定制设计部门，如果你需要测试一下压力您的申请盖章。注：客户或用户有责任确保所有液体和气体都被安全地容纳如果接近型探头发生泄漏，则应予以控制。此外，pH值高或低的溶液可能腐蚀探针尖端组件，导致介质腐蚀泄漏到周围区域。Bently Nevada，股份有限公司将对因以下原因造成的任何损害不承担责任3300 XL 8 mm接近型探针泄漏。此外，3300XL 8 mm接近型探针不会在探头泄漏导致的维修计划。铝夹支架为无螺纹安装支架设计用于光滑外壳探针（330140、330141、330197和330198）。
在探头之间留出间隙后，拧紧夹紧支架拧紧螺钉。
安装螺钉有安全线预钻。
铝探头螺纹安装支架137492-AXX型A： 螺纹尺寸0 1 3/8-24
0 4 M10 x 1铝探头螺纹安装支架为大多数3300和3300 XL探头安装。-01选项包括两个10-24 UNC-2A安装螺钉。-04选项包括两个M5 x 0.8-6g安装螺钉。这个为了安全起见，安装螺钉有预先钻孔金属丝酚醛螺纹探针安装支架27474年XX月
A： 螺纹尺寸0 1 3/8-240 4 M10 x 1我们建议使用酚醛螺纹安装如果应用程序需要额外的与安装位置的电气隔离（如一些发电机和电机轴承位置）。-01选项包括两个10-24 UNC2A安装螺钉。-04选项包括两个M5x 0.8-6g安装螺钉。安装螺钉预先钻好安全线孔。
Probe Pressure
3300 XL 8 mm probes are
designed to seal differential
pressure between the probe tip
and case. The probe sealing
material consists of a Viton®
O-ring. Probes are not pressure
tested prior to shipment. Contact
our custom design department if
you require a test of the pressure
seal for your application.
Note: It is the responsibility of the customer or user to ensure
that all liquids and gases are contained and safely
controlled should leakage occur from a proximity probe.
In addition, solutions with high or low pH values may
erode the tip assembly of the probe causing media
leakage into surrounding areas. Bently Nevada, Inc. will
not be held responsible for any damages resulting from
leaking 3300 XL 8 mm proximity probes. In addition, 3300
XL 8 mm proximity probes will not be replaced under the
service plan due to probe leakage.
The aluminum clamp bracket is an unthreaded mounting bracket designed for use with the smooth case probes (330140, 330141, 330197 and 330198). After gapping the probe, tighten the clamp bracket by tightening the screws. The mounting screws have pre-drilled holes for safety wire. Aluminum probe threaded mounting bracket 137492-AXX A: Thread size 0 1 3/8-24 0 4 M10 x 1 The aluminum probe threaded mounting bracket is the standard mounting bracket for most 3300 and 3300 XL probe installations. The -01 option includes two 10-24 UNC-2A mounting screws. The -04 option includes two M5 x 0.8-6g mounting screws. The mounting screws have pre-drilled holes for safety wire. Phenolic threaded probe mounting bracket 27474-AXX A: Thread size 0 1 3/8-24 0 4 M10 x 1 We recommend the phenolic threaded mounting bracket if your application requires additional electric isolation from the mounting location (as in some generator and electrical motor bearing locations). The -01 option includes two 10-24 UNC2A mounting screws. The -04 option includes two M5 x 0.8-6g mounting screws. The mounting screws have pre-drilled holes for safety wire.
