您的浏览器版本过低,为保证更佳的浏览体验,请点击更新高版本浏览器

以后再说X

欢迎访问瑞昌明盛自动化设备有限公司网站!

图片名

全国订购热线:
+86 15270269218E-mail:stodcdcs@gmail.com

ABB >>

A-B>>

GE>>

BENTLY>>

WESCOM D200 VME燃机电气卡件

WESCOM D200 VME燃机电气卡件

公司主营产品图展示产品优势1:国外专业的供货渠道,具有价格优势2:产品质量保证,让您售后无忧3:全国快递包邮4:一对一服务产品详情介绍WESCOM D200 VME燃机电气卡件有以下两种主要模块类型:–二进制模块。这些模块由二进制I/O操作数的平均值(分别为E或A)。机器人耦合器ICBG 32 L7和ICBG 64 L7(通常用作奴隶)也属于他们,以及中央单元07 KR 91、07 KT 92、0...

  • 功能特性
  • 参数规格
  • 视频
  • 应用案例
  • 下载

WESCOM D200 VME燃机电气卡件

    公司主营产品图展示

    微信图片_20220919175923.jpg

    产品优势

    1:国外专业的供货渠道,具有价格优势

    2:产品质量保证,让您售后无忧

    3:全国快递包邮

    4:一对一服务

    产品详情介绍

    WESCOM D200 VME燃机电气卡件

    有以下两种主要模块类型:–二进制模块。这些模块由二进制I/O操作数的平均值(分别为E或A)。

    机器人耦合器ICBG 32 L7和ICBG 64 L7(通常用作奴隶)也属于他们,以及中央单元07 KR 91、07 KT 92、07 KT93、,07 KR 31和07 KT 31,如果它们被用作奴隶。

    –模拟模块。这些模块由字I/O操作数(EW或AW,分别)。中央单元07 KR 91、07 KT 92、,07 KT 93和高速计数器ICSF 08 D1,接收其预设数据例如,作为单词数据。下表包含模块概述类型。这些名称将在示例6中使用。请注意,可配置的二进制模块ICSC 08 L1和ICFC 16 L1的表现不同到执行的设置。I/O配置A3.1 I/O配置的目的模块根据I/O模块的类型,

    以下各项可以配置:

    对于二进制I/O模块,输入延迟不同出厂设置,如果是带有组合I/O的二进制模块通道,这些通道也可以定义为仅输入或仅输出,如果是二进制模块,则在输入和输出,如果是模拟模块,测量或输出与出厂设置不同的范围。切换输入和输出,打开诊断功能和更改测量和输出范围执行如下,具体取决于模块类型:通过CS31系统执行I/O配置总线,通过总线的用户程序主中央单元或通过终端插入式底座ECZ或输入/输出模块后侧输入/输出模块端子上的外部接线。

    在某些情况下,设置之间存在关系远程模块上的信息和可以在远程模块或通过CS31系统总线。这种关系将在以下章节中进行解释。您无需执行I/O配置如果出厂设置足够,则通过CS31系统总线。执行I/O配置后,它将保持存储在相应的I/O模块中,到再次更改。即使断电,也不会删除。I/O configuration A3.1 Purpose of the I/O configuration of I/O modules Dependent on the type of I/O modules the following can be configured:  in case of binary I/O modules, an input delay different from the factory setting,  in case of binary modules with combined I/O channels, these channels can also be defined as input only or output only,  in case of binary modules, open-circuit monitoring at inputs and outputs,  in case of analog modules, measuring or output ranges which differ from the factory setting. Switching over of inputs and outputs, switching on the diagnosis functions and changing the measuring and output ranges are performed as follows, depending on the module type:  Performing the I/O configuration via the CS31 system bus, either by means of the user program of the bus master central unit or by means of a terminal  Setting of switches on the plug-in base ECZ or on the rear side of the input/output module  External wiring on the input/output module terminals. In some cases, there is a relation between the settings made on the remote module and the information and diagnosis messages which can be interrogated at the remote module or via the CS31 system bus. This relation will be explained in the following chapters. There is no need for you to perform an I/O configuration via the CS31 system bus if the factory setting is sufficient. Once an I/O configuration has been performed, it will remain stored in the corresponding I/O module until it is changed again. Even in case of power OFF it will not be deleted.

    品牌:GE

    型号:WESCOM D200 VME

    产地:美国

    质保:365天

    成色:全新/二手

    发货方式:快递发货


图片名 客服

在线客服 客服一号