公司主营产品图展示
产品优势
1：国外专业的供货渠道，具有价格优势
2：产品质量保证，让您售后无忧
3：全国快递包邮
4：一对一服务
产品详情介绍
FOXBORO 0303440C+0303458A工控卡件
模块有一个内部参考接头。这个将此结的温度值添加到热电偶测量的温度。分辨率12位+符号（1 LSB=0.4°C）评估误差在0…+1600°C+/-满量程的0.5%范围内（线性、线性化、温度范围，分辨率，调整）电缆长度，如果电缆平行敷设屏蔽最大50 m双芯屏蔽，横截面>0.5 mm2，最大200 m未使用的通道必须短路连接至ABB Procontic CS31系统总线接口标准EIA RS–485电气隔离与电源电压和输入-装置在通电后自动初始化。-初始化后，错误指示灯熄灭。模拟输入I0的值显示在6个led上右侧，led的«+5 V»和«±15 V»照亮。● 选择电流或电压电流或电压输入之间的选择取决于在插入式底座上的接线上。当装置为配置为4…20 mA，显示可用范围在下表中。必须配置模拟输出因为出厂默认设置为±10 V。
装置在通电后自行初始化
初始化后，错误指示灯熄灭。的值模拟输出00显示在右侧的8个led上led的«+5V»和«±15V»点亮。对于UCZA/UCZB，地址08…14只允许与SCZ单元一起使用。对于PC板07 CM 90和耦合器板07 CS 61或35 CS 91，请参阅其各自的说明。● 具体配置：ICSM 06 A6作为二进制远程单元ICSM 06 A6远程装置可用作二进制CS31总线上的远程单元。此特定配置允许连接31CS31总线上的模拟远程单元，而不是12。这意味着可以发送或接收所有模拟值由中央单元作为二进制值。模拟/二进制和二进制/模拟转换是由远程单元实现。二进制配置的设置使用双列直插式开关插件底座的2和3位于on位置。在这种情况下（二进制配置），只有偶数地址允许，远程单元的实际地址为由物理地址乘以2得到。对于PC板07 CM 90和耦合器板07 CS 61和35 CS 91，请参阅其各自的说明。注：此特定配置允许在带有07 CS 61耦合器的CS31总线上使用大量远程单元。
ICSM 06 A6仅使用64个I/O点（而不是128个）。T200配置表的代码为EA32。中央单元必须在模拟配置中设置模式4-20 mA，然后移动开关2和3处于ON位置。在模式4-20 mA下，不可能检测到开路。该值始终为0，从不为负。
The module has an internal reference junction. The
temperature value of this junction is added to the
temperature measured by the thermocouple.
Resolution 12 bits + sign (1 LSB = 0.4°C)
Evaluation error within the range of 0...+1600°C +/– 0.5 % of full scale
(linearity, linearization, temperature range,
resolution, adjustment)
Cable length, if cables have been laid in parallel
shielded max. 50 m
two-core shielded and cross section > 0.5 mm2 max. 200 m
Unused channels have to be short–circuited
Connection to the ABB Procontic CS31 system bus
Interface standard EIA RS–485
Electrical isolation versus supply voltage and inputs - The unit initializes itself after power ON.
- The error led goes out after initialization.
The value of the analog input I0 is displayed on the 6 led’s
on the right and the led’s «+ 5 V» and «± 15 V» are
illuminated.● Selection current or voltage
The selection between current or voltage input is dependent
upon the wiring on the plug-in base. When the unit is
configured for 4 … 20 mA, the ranges available are shown
in the table below. The analog outputs must be configured
as the factory default setting is ± 10 V.The unit initializes itself after power on.
The error led goes out after initialization. The value of the
analog output 00 is displayed on the 8 led's on the right
and the led's «+ 5V» and «± 15V» are illuminated.In the case of UCZA/UCZB, the addresses 08 … 14 are only allowed with the SCZ unit.
For the PC board 07 CM 90 and the coupler boards 07 CS 61 or 35 CS 91, refer to their own description.
● Specific configuration : ICSM 06 A6 as binary remote
unit
The ICSM 06 A6 remote unit can be used as a binary
remote unit on the CS31 bus.
This specific configuration allows the connection of 31
analog remote units on CS31 bus instead of 12.
That means that all analog values can be sent or received
by the central unit as binary values.
The analog/binary and binary/analog conversions are
realized by the remote unit.
The setting of binary configuration is with the dip switches
2 and 3 of the plug-in base on ON position.
In this case (binary configuration), only the even addresses
are allowed and the real address of the remote unit is
obtained by the physical address multiplied by 2.
For the PC board 07 CM 90 and the coupler boards 07 CS 61 and 35 CS 91, refer to their own description.
Note : This specific configuration allows a high number of remote units on CS31 bus with the 07 CS 61 coupler.
The ICSM 06 A6 uses only 64 I/O points (instead of 128). The code for T200 configuration table is EA32.
The mode 4 - 20 mA has to be set in analog configuration by the central unit then, the switches 2 and 3 are moved
in ON position.
In mode 4 - 20 mA, it is not possible to detect on opened circuit. The value is always 0 and never negative.
