公司主营产品图展示
产品优势
1：国外专业的供货渠道，具有价格优势
2：产品质量保证，让您售后无忧
3：全国快递包邮
4：一对一服务
产品详情介绍
UFC760BE142控制驱动板
预期用途二进制输入模块ICPI 08 D1是一个远程模块在CS31系统总线上。它有16个二进制通道以下功能：外壳和终端系统符合IP65防护等级CS31总线从模块到单元为此，模块有两条总线连接器作为总线输入和总线输出。每个输入都有自己的连接器，因此可以单独拔下。
24 V DC电源电压通过以下方式连接模块外壳内的螺旋式端子。
输入允许您将传感器与2极和三极技术（开关触点、启动器等）
提供短路/过载保护电源传感器的电压，可加载每个传感器100 mA
每个额定信号电流为15 mA模块用螺钉安装。有钻孔可安装在后壁或水平表面。传感器输入接头处的电源连接通过温度相关电阻器连接（PTC热敏电阻）至螺钉式+24 V DC输入端终端。如果传感器发生过载或短路，PTC将起过载保护作用。A.电压监测电路产生错误信息在欠压情况下（LED“过载”亮起）。
下图演示了该函数。短路或过载消除后，模块可以再次正常运行。红色LED“过载”熄灭。
发送给主机的错误消息：如果发生短路或过载，错误消息连同错误代码一起发送给主服务器4号。在每种情况下，信道0都被视为故障，独立于真正涉及的渠道。错误消息保持至少5秒，甚至如果短路或过载已在时间更短。有关诊断的更多信息，请参阅用作总线的中央单元和耦合器的说明masters远程模拟输入/输出装置用于测量物理过程值。这些单位可以将模拟值转换为数值输入或数值到输出的模拟值。
有两种可用的解决方案：
● 8位单位：-ICSM 06 A6，4个输入，2个输出
-ICSE 08 A6，8个输入
-ICST 08 A8，8输入PT 100
-ICST 08 A9，8输入PT 100
● 12位单位：-ICSE 08 B5，8输入
-ICSA 04 B5，4输出可以使用装置的每个通道进行电流或电压处理。
PT 100通道仅用于温度测量
以下范围有三种可能的配置字内使用的位。
字内使用的位的范围由插入式底座的双列直插式开关N°2和N°3的位置
Intended purpose
The binary input module ICPI 08 D1 is a remote module
on the CS31 system bus. It has 16 binary channels with
the following features:
Housing and termination system according to IP65
degree of protection
The CS31 bus line is looped through from module to
module. For this purpose, the module has two bus
connectors as bus input and bus output.
Each input has its own connector and thus can be
unplugged individually.
The 24 V DC supply voltage is connected via
screw–type terminals inside the module housing.
The inputs
allow you to connect sensors with 2–pole and
3–pole technique (switching contacts, initiators
etc.)
provide a short–circuit/overload–proof supply
voltage for the sensors, with can be loaded with
100 mA by each sensor
have a rated signal current of 15 mA each
The module is mounted with screws. There are bore holes
available for both mounting on a rear wall or on a
horizontal surface.The supply connections at the sensor input connectors
are connected via a temperature–dependent resistor
(PTC thermistor) to the +24 V DC input of the screw–type
terminals. If an overload or a short–circuit occurs with a sensor, the PTC will work as an overload protection. A
voltage monitoring circuitry generates an error message
in case of undervoltage (the LED ”Overload” lights up).
The following figure demonstrates the function.After the short–circuit or overload has been eliminated,
the module can operate correctly again. The red LED
”Overload” goes out.
Error message to the master:
In case of a short–circuit or an overload, an error
message is sent to the master, along with the error code
No. 4. In each case, the channel No. 0 is given as faulty,
independent of the really involved channel. The error
message is kept up for a period of at least 5 seconds, even
if the short–circuit or overload has been remedied in a
shorter time.
Fur further information concerning diagnosis, see the
descriptions of the central units and couplers used as bus
masters The remote analogue input/output units
are used to measure physical process values.
These units can convert analog values to numeric values
for inputs or numeric values to analog values for outputs.
There are two available resolutions :
● 8 bits units:
- ICSM 06 A6, 4 inputs, 2 outputs
- ICSE 08 A6, 8 inputs
- ICST 08 A8, 8 inputs PT 100
- ICST 08 A9, 8 inputs PT 100
● 12 bits units :
- ICSE 08 B5, 8 inputs
- ICSA 04 B5, 4 outputs
It is possible to use each channel of a unit for current or
voltage processing.
The PT 100 channels are only used for temperature
measurement.
There are three possible configurations for the range of
bits used within a word.
The range of bits used within a word is determined by the
position of dip switches N°2 and N°3 of the plug-in base
