3BHE029110R0111控制器模块
输入电源（端子P1和P2）：通电前连接，请参阅发电机随附的接线图。
按如下方式连接输入电源。
-当稳压器设计为120 Vac±10%输入功率时，以及65 Vdc最大连续输出，连接单相120 Vac
端子P1和P2的电源。建议使用上述负载隔离和电压匹配变压器。
-当调节器设计用于240 V ac±10%输入功率时，以及125 Vdc最大连续输出，连接单相240 Vac端子P1和P2的电源。建议使用上述负载隔离和电压匹配变压器。
-当调节系统配有电磁阀时干扰 滤波器，按接线图所示连接与发电机组一起提供。
输出功率（端子F+和F-）：确保调节器输出匹配发电机励磁机额定值。KCR 760电压调节器设计用于：120 Vac输入设计用于65 Vdc最大连续输出。这个KCR 760电压调节器设计用于240 Vac输入，设计用于：125 Vdc最大连续输出。
保持调节器输出和励磁机之间的正确极埃尔德。
确保 65 Vdc调节器的eld电阻不小于6.5和 125 Vdc调节器的eld电阻不小于12.5。
确保 eld电路未接地和/或开路或短路发电机组运行期间。
因为稳压器输出引线未连接到除励磁机外的系统 埃尔德，他们不是 过滤。减少传导EMI应使导线尽可能短并屏蔽。
通过将两根引线穿过0.5一英寸导管。一般情况下，未屏蔽的距离不得超过1至2英尺属于 eld领先。如果发电机内安装了电压调节器出线盒，可以在短时间内获得满意的结果非屏蔽导线。
接地：良好的电源接地不一定是良好的地面电磁干扰。使接地导线尽可能短最好是宽度为长度的1/5的铜带。将机箱接地使所有接地共用。
Input power (terminal P1 and P2): Before making electrical connections, refer to the wiring diagram provided with the generator. Connect input power as follows. - When the regulator is designed for 120 Vac ±10% input power and 65 Vdc maximum continuous output, connect single-phase 120 Vac power to terminals P1 and P2. Refer above for recommended use of load isolation and voltage matching transformers. - When the regulator is designed for 240 V ac ±10% input power and 125 Vdc maximum continuous output, connect single-phase 240 Vac power to terminals P1 and P2. Refer above for recommended use of load isolation and voltage matching transformers. - When the regulating system is supplied with electromagnetic interference lters, connect as shown on the wiring diagram provided with the generator set. Output power (terminals F+ and F-): Be sure regulator output matches the generator exciter rating. The KCR 760 voltage regulator designed for 120 Vac input is designed for 65 Vdc maximum continuous output. The KCR 760 voltage regulator designed for 240 Vac input is designed for 125 Vdc maximum continuous output. Maintain correct polarity between the regulator output and exciter eld. Make sure eld resistance for the 65 Vdc regulator is not less than 6.5 and eld resistance for the 125 Vdc regulator is not less than 12.5 . Make sure the eld circuit is not grounded and/or opened or shorted during operation of the generator set. Because the regulator output leads are not connected to any part of the system except the exciter eld, they are not ltered. To minimize conducted EMI the keep the leads as short as possible and shielded. Effective shielding can be attained by routing both leads through 0.5 inch conduit. In general, do not leave unshielded more than 1 to 2 feet of eld leads. If the voltage regulator is installed within the generator outlet box, it is possible to achieve satisfactory results with short unshielded leads. Grounding: A good electrical power ground is not necessarily a good electromagnetic interference ground. Make the ground leads as short as possible, preferably of copper strap with a width of 1/5 the length. Grounding the chassis to earth ground makes all grounds common.
