3BSE019216R1数字信号卡件
90-70系列总线控制器和网络的硬件配置
从Control 90机架显示器中选择总线控制器以编辑硬件
总线控制器和网络的配置。选择工具后，进行编辑硬件配置，以下选项卡可用：
设置I/O机架驱动器
可编程逻辑控制器
站（控制站）通用设备扫描通讯员
协议文件功耗
选择后，这些选项卡显示从FIP配置的参数网络配置工具。已使用网络配置的参数配置工具仅在更新后显示。
设置
选择设置选项卡以配置总线控制器。总线的不可编辑项控制器包括是否是主用户、是否是总线仲裁器、时钟
同步等。状态数据长度（80位或5字）不可编辑，但是您可以更改当前分配给总线的参考地址
控制器的状态数据。IP地址、子网掩码和网关IP地址应分配给您的网络管理员。如果地址
设置不正确，您的设备可能无法通过网络和CAN进行通信
中断通信。对于没有网关的简单隔离网络，分配格式为3.0.0.x（x）的唯一地址
范围从1到255）。协议文件
最多可在此处输入8个用户协议文件的目录路径规范。通讯员
显示与此FIP总线控制器交换I/O数据的所有设备的列表。
所有字段都不可编辑
–如果“受控设备”为否，则该设备仅由FIP总线控制器监控。
FIP总线控制器不能配置或影响I/O的操作模式支架
–如果“受控设备”为是，则该设备由FIP总线控制器控制。这个FIP总线控制器可以配置设备并控制其工作模式。I/O机架、驱动器、PLC、工作站和通用设备根据需要选择I/O机架、驱动器、PLC、工作站和通用设备选项卡，以：配置网络上的设备。这些选项卡上的不可编辑项包括设备名称、机架、插槽、TVA类型以及所列设备是否生产或消费数据为各个设备配置以下参数。
Hardware Configuration for the Series 90-70 Bus Controller and the Network
Select the Bus Controller from the Control 90 rack display to edit the Hardware
Configuration for the Bus Controller and the network. When you select Tools then Edit
Hardware Configuration, the following tabs are available:
Settings
I/O Racks
Drives
PLCs
Stations (control stations)
Generic Devices
Scanning
Correspondents
Protocol Files
Power Consumption
When selected, these tabs display parameters that have been configured from the FIP
Network Configuration tool. Parameters that have been configured with the Network
Configuration Tool appear only after an update.
Settings
Select the Settings tab to configure the Bus Controller. Non-editable items for the Bus
Controller include whether it is the master subscriber, whether it is the bus arbiter, clock
synchronization, and others. The status data length (80 bits or 5 words) is not editable,
but you can change the reference address that is presently assigned for the Bus
Controller’s status data.The IP Address, Subnet Mask, and Gateway IP Address should be assigned by
your network administrator. If addresses
are improperly set, your device may not
communicate on the network and could
disrupt communications. For a simple, isolated network with no gateways, assign a
Unique address in the format 3.0.0.x (x
ranges from 1 to 255).Protocol Files
Directory path specifications for up to 8 User Protocol Files may be entered here.
Correspondents
A list of all the devices that exchange I/O data with this FIP Bus Controller is displayed.
All the fields are non-editable.
– If “Controlled Device” is NO, this device is only monitored by the FIP Bus Controller.
The FIP Bus Controller cannot configure or affect the operating mode of the I/O
rack.
– If “Controlled Device” is YES, this device is controlled by the FIP Bus Controller. The
FIP Bus Controller can configure the device and control its operating mode.
I/O Racks, Drives, PLCs, Stations , and Generic Devices
Select the I/O Racks, Drives, PLCs, Stations, and Generic Devices tabs as necessary to
configure the devices on the network. Non-editable items on these tabs include the
device name, rack, slot, TVA type, and whether the listed devices produce or consume
data. Configure the following parameters for individual devices.
