主营产品
PLC可编程控制器模块，DCS卡件，ESD系统卡件，振动监测系统卡件，汽轮机控制系统模块，燃气发电机备件等，优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件
产品广泛应用于冶金、石油天然气、玻璃制造业、铝业、石油化工、煤矿、造纸印刷、纺织印染、机械、电子制造、汽车制造、塑胶机械、电力、水利、水处理/环保、锅炉供暖、能源、输配电等等
3BHE0Q4573R1142逻辑顺序卡件
•将信号线与负荷线分开布线，以避免干扰。
•通过屏蔽传导模拟信号（如命令/实际值）引导。
•电源、直流母线和电源线不应连接至低电压或与它们接触。
•在进行任何高压或外部电压测试时加工驱动部件的所有信号和电源连接
必须移除。这可保护电子部件（允许根据EN 60204-1）。力士乐Indramat驱动组件按照EN 50178进行高压和绝缘测试。要释放驱动，必须提供继电器+处的驱动锁定释放装置具有24V。该电压为X4引脚1。如果使用该内部电压源，则不必连接X4引脚2。如果外部24V为电压源，则必须连接到X4引脚3继电器+和X4引脚20V。ASQ，ASQ：无电势反馈触点，确认开始锁定外部控制装置。
制动容量：直流24 V，1 A（最大=持续时间）
驱动控制器中启动锁定继电器的启动为：
通过关闭无电势反馈触点（输出）确认ASQ-ASQ）发送到外部控制。应使用力士乐Indramat电机电源电缆连接驱动器控制器和电机。在力士乐Indramat电机电缆内，有：
•电机电源连接的三条电源线，以及
•一条线路用于接地导线连接•电机温度监测器的一对单独屏蔽线
•电机保持制动器的单独屏蔽线对
•以及安装在屏蔽附件上的完整屏蔽。
电机电源电缆作为力士乐的标准电缆提供
因德拉马特。电缆也可以由四个绞合的独立电源组成
线路（3相，1根接地导线）具有单独传导的，
用于温度监测和制动器连接的屏蔽电源线。
有关连接和直径的补充技术信息，参见相关电机说明。
如果力士乐Indramat电缆：习惯于相邻的驱动器控制器通常通过利兹线连接
（随驱动器一起提供）。如果不可能使用这些连接线，则使用短至以下的扭绞电源线建立连接：
可能（最大长度为1米，最大直径为16 mm²）。
Route signal lines separately from load lines to avoid interference.
• Conduct analog signals (e.g., command/actual values) via shielded
leads.
• Mains, DC bus and power lines should not be connected to low
voltages or come into contact with them.
• When carrying out any high voltage or external voltage testing of the
machine all signal and power connections to the drive components
must be removed. This protects the electronic components (allowed
as per EN 60204-1). Rexroth Indramat drive components are highvoltage and insulation tested as per EN 50178.To release the drive, the drive lockout release at relay + must be supplied
with 24V. This voltage is at X4 pin1. If this internal voltage source is used,
then X4 pin2 does not have to be connected. If an external 24V is the
voltage source, then it must be connected to X4 pin3 relay+ and X4 pin2
0V.
ASQ, ASQ:
Potential-free feedback contact which acknowledges the actuating of the
starting lockout to an external control.
Braking capacity: DC 24 V, 1 A (maximum = duration)
The actuation of the relay of the starting lockout in the drive controller is
confirmed by the closing of the potential-free feedback contact (output
ASQ - ASQ) to the external control.Rexroth Indramat motor power cables should be used to connect drive
controller and motor.
Inside an Rexroth Indramat motor power cable there are
• three supply lines for the motor power connection and
• one line for the ground conductor connection
• a separately shielded pair of lines for the motor temperature monitor
• a separately shielded pair of lines for the motor holding brake
• and a complete shield mounted to the shield attachment.
The motor power cable is available as a standard cable from Rexroth
Indramat. The cable can also be made of four twisted individual supply
lines (3 phases, 1 grounded conductor) with a separately conducted,
shielded supply line for temperature monitoring and the brake connection.
For supplementary technical information on connections and diameters,
see the relevant motor description.
Maximum cable lengths equal 75 meters if Rexroth Indramat cables are
used.
Adjacent drive controllers are generally connected via the litz wires
(shipped with the drive).
If it should not be possible to use these connecting litz wires, then
establish the connection with twisted supply lines that are as short as
possible (maximum length of one meter, maximum diameter 16 mm²).
