3BSC980006R152工控卡件
该模块使用操作员面板操作，该面板包括使用输入MD打开的绿色和红色LED。
HI（1）输入将点亮绿色LED，LO将点亮红色LED。默认连接将是的PS输出
但应根据需要进行更改，以显示正确的状态。消息参数不适用于当前产品。
通电-当交换机配置为：瞬时动作，它将始终在NC位置。对于持续行动，与通电参数设置为“是”，开关将在炎热或温暖天气下，在最后一个位置通电启动，在冷启动期间，将在NC位置。当加电参数为设置为“否”，开关将在最后一次通电热启动期间的位置。在温暖或寒冷期间启动时，它将在NC位置通电。PB3SW是三种通用开关之一，在每个循环中可用。它可以用于切换布尔信号在以下应用中：启动/停止，控制TSW（转换开关）的位置用于切换模拟信号的功能块，或其他操作员启动操作。PB3SW只能运行当A/M功能块具有未配置。PB3SW可配置为瞬时或持续活动作为瞬时，开关将切换到按下按钮时无位置，按钮将返回
当释放时。在持续模式下，开关将每次按下按钮时的交替位置。一未配置的NC输入默认为0，并且未配置无输入1。固件为1.30和更高，按钮可以通过通过Modbus或LIL的命令。
该模块使用操作员面板操作，该面板包括使用输入MD打开的绿色和红色LED。
HI（1）输入将点亮绿色LED，LO将点亮红色LED。默认连接将是的PS输出
但应根据需要进行更改，以显示正确的状态。消息参数不适用于
当前产品。通电-当交换机配置为：瞬时动作，它将始终在NC位置。对于持续行动，与通电参数设置为“是”，开关将在炎热或温暖天气下，在最后一个位置通电启动，在冷启动期间，它将在NC位置。当加电参数为设置为“否”，开关将在最后一次通电热启动期间的位置。在温暖或寒冷期间start将在NC位置通电。
This block operates with an operator faceplate that includes green and red LEDs that are turned on using input MD.
A HI (1) input will turn on the Green LED and a LO the Red LED. The default connection will be the PS output of
the block but should be changed as required to display the correct status. The message parameters do not apply to
the current product.
POWER UP - When the switch is configured for
momentary action, it will always power up in the
NC position. For sustained action, with the
POWER UP parameter set to YES, the switch will
power up in the last position during a hot or warm
start, and during a cold start will power up in the
NC position. When the POWER UP parameter is
set to NO, the switch will power up in the last
position during a hot start. During a warm or cold
start, it will power up in the NC position.PB3SW is one of three general purpose switches,
available in each loop. It can be utilized for switching
Boolean signals in such applications as: Start/Stop,
controlling the position of a TSW (Transfer Switch)
function block for switching analog signals, or other
operator initiated actions. PB3SW can only be operated
from the front panel when the A/M function block has
not be configured.
PB3SW can be configured for momentary or sustained
operation. As momentary, the switch will transfer to the
NO position when the button is pressed and it will return
when released. In the sustained mode, the switch will
alternate positions each time the button is pressed. An
unconfigured NC input defaults to 0 and an
unconfigured NO input to 1. With firmware 1.30 and
higher, the button can be remotely activated through a
command over Modbus or LIL.
This block operates with an operator faceplate that includes green and red LEDs that are turned on using input MD.
A HI (1) input will turn on the Green LED and a LO the Red LED. The default connection will be the PS output of
the block but should be changed as required to display the correct status. The message parameters do not apply to
the current product. POWER UP - When the switch is configured for
momentary action, it will always power up in the
NC position. For sustained action, with the
POWER UP parameter set to YES, the switch will
power up in the last position during a hot or warm
start, and during a cold start it will power up in the
NC position. When the POWER UP parameter is
set to NO, the switch will power up in the last
position during a hot start. During a warm or cold
start will power up in the NC position.
