P0916CQ脉冲输入模块
DOD_功能块最多传输16个开/关信号从控制器块互连接收到远程LonWorks网络上的节点。最大6 DOD可以使用块，但不超过上允许的节点数Lon网络或控制器的内存限制。
每个区块的使用都将分配一个唯一的桩号宽ID（如DOD01）。传输的每个输入类型为：SNVT_lev_disc，可以绑定到中的网络变量可以接收网络的单个或多个远程节点此类型的变量。这些区块将在以下情况下可用：
LonWorks选项板安装在352P、353或354N控制器。0 NV NUM参数启用工作站分配给输入0的编号
查看。
所有后续网络变量均已分配连续地。
每个功能块输入具有与其关联的模式。模式可以是正常模式或强制模式。什么时候使用能够发送LIL或Modbus命令的PC，模式可以改变，强制状态可以改变分配高（1）或低（0）值。价值观两个输入（F和N）可通过网络访问以及SPDT开关的位置，如框图。“0”模式正常，“1”模式正常强迫。每个功能块输入还具有相关的质量状态用它。当模块确定时，该状态将变为高（1）它已与绑定到该节点的Lon节点失去通信
输入如果任何单个质量输入较高，则质量状态块输出也将很高。DOE_功能块在以下情况下可用：安装了以太网通信板。最多32个DOE块可用，并按顺序分配给每个块使用，全站性。最多可配置16个数字输入。该区块将将输入I0-IF打包为单个整数字，该整数字可以是从另一个具有以太网的控制器访问通信能力。
每个DOE块自动分配Modbus可以从任何具有Modbus以太网功能。当可选的LIL时，DOL_功能块可用已安装通信板。他们允许车站：输出全局字GW，其中位0-F表示状态每个布尔输入D0-DF的1或0。未配置输入设置为0。DOL块编号在每次使用的顺序，全站范围。
2DOD_ function blocks transmit up to 16 on/off signals
received from a controller block interconnection to remote
nodes on the LonWorks network. A maximum of 6 DOD
blocks can be used, up to the limit of nodes allowed on
the Lon network or the memory limit of the controller.
Each use of the block will be assigned a unique station
wide ID (e.g. DOD01). Each input transmitted is of type
SNVT_lev_disc and can be bound to network variables in
a single or multiple remote nodes that can receive network
variables of this type. These blocks will be available when
the LonWorks option board is installed in a 352P, 353, or
354N controller. The 0 NV NUM parameter enables the
number that the station has assigned to input 0 to be
viewed. All subsequent network variables are assigned
consecutively.
Each function block input has a mode associated with it.
The mode can be either NORMAL or FORCED. When
using a PC capable of sending LIL or Modbus commands,
the mode can be changed and the forced state can be
assigned a high (1) or low (0) value. The values
accessible over the network are the two inputs (F and N)
and the position of the SPDT switch illustrated in the
block diagram. A mode of ‘0’ is Normal and ‘1’ is
Forced. Each function block input also has a quality status associated
with it. This status will go high (1) when the block determines
it has lost communication with the Lon node bound to that
input. If any of the individual quality inputs are high, the
Quality Status block output will also be high. DOE_ function blocks are available when the optional
Ethernet communication board is installed. Up to 32 DOE
blocks are available and are assigned in sequence with each
use, station wide.
Up to 16 digital inputs can be configured. The block will
pack inputs I0 - IF into a single integer word which can be
accessed from another controller having Ethernet
communication capability.
Each DOE block is automatically assigned Modbus
registers that can be accessed from any device having the
Modbus Ethernet capability. DOL_ function blocks are available when the optional LIL
communication board is installed. They allow the station to
output a global word GW with bits 0-F representing the state
1 or 0 of each of the Boolean inputs D0 - DF. Unconfigured
inputs are set to 0. DOL block numbers are assigned in
sequence with each use, station wide.
