UFC760BE41控制卡,3BHE004573R0041配置手册
创建分区方案后，可以将分区格式化为包含所需的文件系统。如前所述，典型系统由VMIVME-7750及其驻留系统组成配置为辅助IDE设备的闪存，连接到主IDE接口，以及连接到软盘接口的软盘驱动器。使用这种配置，可能需要在任一IDE上都有一个逻辑设备设备，配置为可引导设备，允许选择第一个引导设备通过先进的CMOS设置屏幕。使用此功能，用户可以配置有多个操作系统的系统，可以通过以下方式进行选择：将IDE逻辑设备指定为引导设备。
UFC760BE41控制卡DOS实用程序FDISK通常用于配置硬盘驱动器。下一页的评论与使用FDISK。注意：删除分区将删除以前存储在该分区中的所有数据隔断闪存盘将配置为从工厂以下示例序列说明了创建两个8 MB分区，其中一个作为活动主分区。注意退出FDISK的说明。这已被证明是成功的分区工作。
1、接通VMIVME-7750电源，进入CMOS设置。
2、将IDE硬盘主机设置为“未安装”。3、将闪存盘主机设置为“自动”。
4、将引导设备设置为软盘。
5.从软盘引导DOS，并验证系统配置屏幕仅显示闪存盘。
6、运行FDISK。
7.删除所有当前分区（当前存储在分区中的任何数据都将被删除丢失）。
8.退出FDISK（这将导致重新启动），然后再次运行FDISK。9.创建一个8MB的主分区。
10.创建一个8兆字节的扩展分区。
11.为8 MB扩展分区设置逻辑设备。
12、将主分区设置为活动分区。
13、退出FDISK。
Following the creation of the partitioning scheme, the partitions can be formatted to
contain the desired file system.
As discussed earlier, a typical system consists of the VMIVME-7750 with its resident
Flash Disk configured as the Secondary IDE device, a hard drive attached to the
Primary IDE interface, and a floppy drive attached to the floppy interface.
Using this configuration, it may be desirable to have a logical device on either IDE
device, configured as a bootable device, allowing the selection of the first boot device
by way of the Advanced CMOS Setup screen. Using this capability, a user could have
a system configured with multiple operating systems that would be selectable by
assigning the IDE logical device as the boot device.
The DOS utility FDISK is commonly used to configure the partition structure on a
hard drive. Comments on the following page pertain to partitioning efforts using
FDISK.
CAUTION: Deleting a partition will erase all the data previously stored in that
partition.
The Flash Disk will be configured as a single partition device as delivered from the
factory. The following sample sequence illustrates a proven method for creating two
8 Mbyte partitions, with one as an active primary partition. Take note of the
instructions to exit FDISK. This has been shown to be an important step in a
successful partitioning effort.
1. Power up the VMIVME-7750 and enter the CMOS set-up.
2. Set IDE HDD Master to “Not Installed”. 3. Set Flash Disk Master to “AUTO”.
4. Set boot device to floppy.
5. Boot DOS from the floppy, and verify that the System Configuration Screen
shows only the Flash Disk.
6. Run FDISK.
7. Delete all current partitions (any data currently stored in the partitions will be
lost).
8. Exit FDISK (this will cause a reboot), then run FDISK again.
9. Create an 8 Mbyte primary partition.
10. Create an 8 Mbyte extended partition.
11. Set-up a logical device for the 8 Mbyte extended partition.
12. Set the Primary partition as an active partition.
13. Exit FDISK.
