P0973JM交换机模块,A4H124-24TX说明书文档
仅显示连接的称重传感器的菜单。service menu（维修菜单）包含只能查看（显示）的参数和可以设置。?只能查看的参数：–版本：XX。十、显示PFEA113软件版本。–最大负载A、最大负载B、最大负载C、最大负载D显示自上次重置以来的最大负载（对于连接的称重传感器）。–PresentOffset A、PresentOffset B、PresentOffset C、PresentOffset D显示最后一个零位设置的零位偏移（对于连接的称重传感器）。
P0973JM交换机模块最大负载/当前偏移对于连接到腹板张力电子装置PFEA113的每个称重传感器，最大负载范围为±6.5 x Fnom的存储器将存储施加到称重传感器的最高负载。最大负载包括：?称重传感器零信号（称重传感器上无负载）?FRT，称重传感器测量方向上皮重的作用力分量和?FR，测得的力（在测量方向上的张力力分量）称重传感器）如果更换称重传感器，则可以重置最大负载内存。可以将模拟设置为打开或关闭。如果模拟设置为开启，参数PercentofNoma和PercentofNomb将为显示。如果在ObjectType和中选择了单侧A，则不会显示百分比OFNOMB如果在ObjectType中选择了单侧B，则不会显示节点百分比。参数percentofnom可以一步一步地设置在-100和+200之间。什么时候simulation设置为ON，它将替换称重传感器的测量值。值+100表示该值与加载到Fnom的称重传感器相同。激活模拟时不能使用零集。当模拟设置为打开时，红色状态led点亮，显示屏上显示消息“Simulation”。如果按下“ok”（确定），则消息以与故障和警告相同的方式移动到操作员菜单的底部信息。SetFactory Default将模拟设置为关闭。当“模拟”设置为“开”时，默认值为：–正常百分比=55%–NOMB百分比=45%Only menus for connected load cells are shown.The service menu has parameters that can be viewed (displayed) only and parameters that canbe set.? Parameters that can be viewed only:– Version: XX.X
Displays PFEA113 software version.– MaximumLoad A, MaximumLoad B, MaximumLoad C, MaximumLoad D
Displays maximum load (for connected load cells) since last reset.PresentOffset A, PresentOffset B, PresentOffset C, PresentOffset DDisplays zero offset (for connected load cells) at last zero set.Maximum Load / Present Offset
For each load cell connected to the web tension electronics PFEA113, a maximum load
memory, with the range ±6.5 x Fnom, will store the highest load that is applied to the load cell.
The maximum load consists of:? load cell zero signal (with no load on the load cell)
? FRT, applied force component of tare in the measuring direction of the load celland
? FR, measured force (force component of tension in the measuring direction of
the load cell)The maximum load memory can be reset if a load cell is replacedSimulation can be set to ON or OFF.
If simulation is set to ON, the parameters PercentOfFnomA and PercentOfFnomB will be
displayed. PercentOfFnomB is not shown if Single side A has been selected in ObjectType and
PercentOfFnomA is not shown if Single side B has been selected in ObjectType.
The parameter PercentOfFnom can be set between –100 and +200 in steps of one. When
simulation is set to ON, it replaces the measured value from the load cells. The value +100
means that the value is the same as load cell loaded to Fnom.
Zero set can not be used when simulation is activated. When simulation is set to ON, the red
status led is lit and on the display the message “Simulation” is shown. If “ok” is pressed, the
message is moved to the bottom of the Operator menu in the same way as failure and warning
messages.
SetFactory Default sets the simulation to OFF.
When simulation is set to ON, the default values are:
– PercentOfFnomA = 55%
– PercentOfFnomB = 45%
